Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 73

Страница: 73 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

2. Removing the inverter assembly, inverter P.C. board

and relay P.C. board

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the lead wire to the reactor and the following con-

nectors:

CN601 (Defrost heater and heater protector) (

MUZ-GL24NAH

)

CN602 (R.V. coil) (

MUZ

)

CN931, CN932 (Fan motor)

CN671 (Defrost thermistor (

MUZ

), discharge temperature

thermistor and outdoor heat exchanger temperature

thermistor)

CN672 (Ambient temperature thermistor)

CN724 (LEV)

(3) Remove the compressor connector.

(4) Remove the screws fixing the relay panel.

(5) Remove the relay panel.

(6) Remove the ground wires and the lead wires of the inverter

P.C. board.

(7) Remove the screws of the P.B. support.

(8) Remove the inverter P.C. board from the P.B. support.

Photo 5

3. Removing R.V. coil (MUZ)

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the following connector:

CN602 (R.V. coil) (

MUZ

)

(3) Remove the R.V. coil.

Photo 6

Brazed parts of

4-way valve

Screw of the

R.V. coil (

MUZ

)

Screw of the

relay panel

Screws of the

P.B. support

Inverter P.C.

board

Ground wires

Screws of

the P.B.

support

Screw of the

relay panel

Screw of the

relay panel

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды