Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 60

Страница: 60 / 76

P Electromagnetic noise enters into TV sets or radios

Is the unit grounded?

Ground the unit.

Is the distance between the antennas

and the indoor unit within 9.91 ft. (3m),

or is the distance between the antennas

and the outdoor unit within 9.91 ft. (3m)?

Extend the distance between the antennas and

the indoor unit, and/or the antennas and the

outdoor unit.

Is the distance between the TV sets or ra-

dios and the indoor unit within 3.28 ft. (1m),

or is the distance between the TV sets or

radios and the outdoor unit within

9.91 ft. (3m)?

Extend the distance between the TV sets and/or

radios and the indoor unit, or the TV sets or

radios and the outdoor unit.

Are the antennas damaged?

Is the coaxial cable damaged?

Is there any poor contact in the anten-

na wiring?

Replace or repair the antenna.

Replace or repair the coaxial cable.

Is the indoor/outdoor connecting wire

of the air conditioner and the wiring of

the antennas close?

Extend the distance between the indoor/outdoor

connecting wire of the air conditioner and the wir-

ing of the antennas.

Even if all of the above conditions are fulfilled, the electromagnetic noise may enter, depending on the electric field strength

or the installation condition (combination of specific conditions such as antennas or wiring).

Check the following before asking for service.

1. Devices affected by the electromagnetic noise

TV sets, radios (FM/AM broadcast, shortwave)

2. Channel, frequency, broadcast station affected by the electromagnetic noise

3. Channel, frequency, broadcast station unaffected by the electromagnetic noise

4. Layout of:

indoor/outdoor unit of the air conditioner, indoor/outdoor wiring, ground wire, antennas, wiring from antennas, receiver

5. Electric field intensity of the broadcast station affected by the electromagnetic noise

6. Presence or absence of amplifier such as booster

7. Operation condition of air conditioner when the electromagnetic noise enters in

1) Turn OFF the power supply once, and then turn ON the power supply. In this situation, check for the electromagnetic

noise.

2) Within 3 minutes after turning ON the power supply, press STOP/OPERATE (OFF/ON) button on the remote controller

for power ON, and check for the electromagnetic noise.

3) After a short time (3 minutes later after turning ON), the outdoor unit starts running. During operation, check for the

electromagnetic noise.

4) Press STOP/OPERATE (OFF/ON) button on the remote controller for power OFF, when the outdoor unit stops but the

indoor/outdoor communication still runs on. In this situation, check for the electromagnetic noise.

Yes

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды