Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 58

Страница: 58 / 76

• Turn OFF inverter-controlled lighting

equipment.

• Turn OFF the power supply and then

turn ON again.

• Press EMERGENCY OPERATION

switch.

Is serial signal

error indicated 6

minutes later?

Yes

• Reinstall

either the unit

or the light

away from

each other.

•

Attach a filter

on remote

control receiv-

ing section

of the indoor

unit.

Turn OFF the power supply.

Is there rated voltage in the power supply?

Yes

Turn ON the power supply.

Check the power supply.

Is there rated voltage between outdoor terminal block S1 and S2? No

Check the wiring.

Press EMERGENCY OPERATION switch once.

Does the OPERATION INDICATOR lamp light

up? <Confirmation of the power to the indoor

unit>

Yes

Is serial signal error indicated 6 minutes

later?

Yes

Is there any miswiring,

poor contact, or wire

disconnection of the

indoor/outdoor connect-

ing wire?

Yes Correct them.

Turn OFF the power supply.

Check once more if the indoor/outdoor

connecting wire is not miswiring.

Bridge the outdoor terminal block S2 and

S3. *1

*1. Miswiring may damage indoor electronic control P.C.

board during the operation.

Be sure to confirm the wiring is correct before the opera

tion starts.

Turn ON the power supply.

Does the LED on the inverter P.C. board or the outdoor electronic control P.C.

board repeat "3.6-second-OFF and 0.8-second-ON quick blinking"? *3

Yes

GL24

GL18

(Lit or

not lit)

Replace the inverter P.C. board or the outdoor

electronic control P.C. board. *2

2. Be careful of the residual voltage of smoothing

capacitor.

Turn OFF the power supply.

Remove the bridge between outdoor terminal block S2 and S3.

Yes

*3. Be sure to check this within 3 minutes after turning ON.

After 3 minutes, LED blinks 6 times. Even when the

inverter P.C. board or the outdoor electronic control P.C.

board is normal, LED blinks 6 times after 3 minutes.

(Except for outdoor unit of multi system type)

Is the bus-bar voltage of the inverter P.C. board or the outdoor electronic control P.C. board normal? (Refer

to "TEST POINT DIAGRAM AND VOLTAGE" in the outdoor service manual.)

Yes

Replace the indoor electronic control P.C. board.

Turn on the power supply.

Is there amplitude of 10 to 20 V DC between the indoor terminal block

S2 and S3? <Confirmation of serial signal>

Yes

Is there 2 V DC or less between CN10A (+)

and GND (-) on the indoor electronic control

P.C. board?

Yes

Is there 2 V DC or less between

CN10A (+) and GND (-) on

the indoor electronic control P.C.

board?

Is there 2 V DC or less between

CN10A (+) and GND (-) on

the indoor electronic control P.C.

board?

Replace the indoor elec-

tronic control P.C. board.

Yes

Replace the indoor power

P.C. board.

MUZ-GL18/24NA

MUZ-GL18/24NAH

MUY-GL18/24NA

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды