Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 66

Страница: 66 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

Photo 4

Photo 5

2. Removing the inverter assembly, inverter P.C. board

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the lead wire to the reactor and the following

connectors:

CN721 (R.V. coil) (

MUZ

)

CN722 (Defrost heater and heater protector) (

MUZ-

GL09/12/15NAH

)

CN931, CN932 (Fan motor)

CN641 (Defrost thermistor (

MUZ

) and discharge tempera-

ture thermistor)

CN643 (Ambient temperature thermistor)

CN644 (Outdoor heat exchanger temperature thermistor)

CN724 (LEV)

(3) Remove the compressor connector (CN61).

(4) Remove the screws fixing the heat sink support and the

separator.

(5) Remove the fixing screws of the terminal block support and

the back panel.

(6) Remove the inverter assembly.

(7) Remove the screw of the ground wire and screw of the ter-

minal block support.

(8) Remove the heat sink support from the P.C. board support.

(9) Remove the screw of the inverter P.C. board and remove the

inverter P.C. board from the P.C. board support.

Photo 6

3. Removing R.V. coil

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the following connectors:

CN721 (R.V. coil) (

MUZ

)

(3) Remove the R.V. coil.

Photo 7

Screws of the heat sink

support and the separator

Screws of the terminal block

support and the back panel

Screws of the

conduit cover

Screw of the

conduit plate

Heat sink

Screw of the

ground wire

Screw of the

Terminal block

support

Screw of the

inverter P.C. board

Heat sink support

P.C. board

support

Terminal

block

support

*U2 model does not

have a screw on the

heat sink support.

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды