Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 74

Страница: 74 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

4. Removing the discharge temperature thermistor,

defrost thermistor (MUZ), outdoor heat exchanger

temperature thermistor and ambient temperature

thermistor

(1) Remove the cabinet and panels. (Refer to section 1.)

(2) Disconnect the lead wire to the reactor and the following

connectors:

CN671 (Defrost thermistor (

MUZ

), discharge temperature

thermistor and outdoor heat exchanger temperature

thermistor)

CN672 (Ambient temperature thermistor)

(3) Pull out the discharge temperature thermistor from its holder.

(4) Pull out the defrost thermistor from its holder.

(5) Pull out the outdoor heat exchanger temperature thermistor

from its holder.

(6) Pull out the ambient temperature thermistor from its holder.

Photo 7

Photo 8

Photo 9

5. Removing outdoor fan motor

(1) Remove the top panel, cabinet and service panel. (Refer to

section 1.)

(2) Disconnect the following connectors:

CN931 and CN932 (Fan motor)

(3) Remove the propeller.

(4) Remove the screws fixing the fan motor.

(5) Remove the fan motor.

NOTE

: The propeller fan nut is a reverse thread.

6. Removing the compressor and 4-way valve

(1) Remove the top panel, cabinet and service panel. (Refer to

section 1.)

(2) Remove the back panel. (Refer to section 1.)

(3) Remove the inverter assembly. (Refer to section 2.)

(4) Recover gas from the refrigerant circuit.

NOTE:

Recover gas from the pipes until the pressure gauge

shows 0 PSIG.

(5) Detach the brazed part of the suction and the discharge

pipes connected with compressor.

(6) Remove the compressor nuts.

(7) Remove the compressor.

(8) Detach the brazed parts of 4-way valve and pipes. (Photo 6)

Screws of the outdoor fan motor

Brazed part of the

discharge pipe

Brazed part of

the suction pipe

Discharge temperature

thermistor

Outdoor heat exchanger

temperature thermistor

Ambient temperature

thermistor

Defrost thermistor (

MUZ

)

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды