Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 47

Страница: 47 / 76

ON
OFF

2.5-second OFF

0.5-second ON

LED

Blinking →

MUZ-GL09/12/15/18NA

MUZ-GL09/12/15/18NAH

MUY-GL09/12/15/18NA

Inverter P.C. board

MUZ-GL24NA

MUZ-GL24NAH

MUY-GL24NA

LED

→

Blinking

No.

Symptom

LED indication

Abnormal point/

Condition

Remedy

Outdoor unit

operates.

1-time blink

2.5 seconds OFF

Frequency drop by

current protection

MUZ-GL09/12/15/18

MUY-GL09/12/15/18

When the input current exceeds ap-

proximately 10.5A, compressor fre-

quency lowers.

The unit is normal, but check the

following.

•

Check if indoor filters are clogged.

• Check if refrigerant is short.

• Check if indoor/outdoor unit air

circulation is short cycled.

MUZ-GL24

MUY-GL24

Current from power outlet is nearing

breaker capacity.

3-time blink

2.5 seconds OFF

Frequency drop by

high pressure pro-

tection

Temperature of indoor coil thermistor exceeds 131 °F (55°C)

in HEAT mode, compressor frequency lowers.

Frequency drop by

defrosting in COOL

mode

Indoor coil thermistor reads 46°F (8°C) or less in COOL mode,

compressor frequency lowers.

4-time blink

2.5 seconds OFF

Frequency drop by

discharge tempera-

ture protection

Temperature of discharge temperature thermistor exceeds

232°F (111°C), compressor frequency lowers.

• Check refrigerant circuit and refrig-

erant amount.

• Refer to 10-5. "Check of LEV".

• Refer to 10-5. "Check of outdoor

thermistors".

5-time blink

2.5 seconds OFF

Outside temperature

thermistor protec-

tion

When the outside temperature thermistor shorts or opens,

protective operation without that thermistors is performed.

• Refer to 10-5. Check of outdoor

thermistors.

7-time blink

2.5 seconds OFF

Low discharge tem-

perature protection

Temperature of discharge temperature thermistor has been

122°F (50°C) or less for 20 minutes.

• Refer to 10-5. "Check of LEV".

• Check refrigerant circuit and refrig-

erant amount.

8-time blink

2.5 seconds OFF

MUZ-GL09/12/15/18

MUY-GL09/12/15/18

PAM protection

PAM: Pulse Ampli-

tude Modulation

The overcurrent flows into PFC (Power factor correction

:IC820) or the Bus-bar voltage reaches 394 V or more, PAM

stops and restarts.

This is not malfunction. PAM pro-

tection will be activated in the fol-

lowing cases:

1 Instantaneous power voltage

drop. (Short time power failure)

2 When the power supply voltage

is high.

MUZ-GL24

MUY-GL24

Zero cross detecting

circuit

Zero cross signal cannot be detected.

• It occurs with following cases.

1 Instantaneous power voltage

drop. (Short time power failure)

2 Distortion of primary voltage

• Refer to 10-5. "Check of power

supply".

9-time blink

2.5 seconds OFF

Inverter check mode The connector of compressor is disconnected, inverter check

mode starts.

• Check if the connector of the com-

pressor is correctly connected.

Refer to 10-5. "How to check

inverter/compressor".

NOTE:

1. The location of LED is illustrated at the right figure. Refer to 10-6.1.

2. LED is lit during normal operation.

3. Blinking patterns of this mode differ from the ones of the failure recall mode.

The blinking frequency shows the number of times the LED blinks after every 2.5-second OFF.

(Example) When the blinking frequency is “2”.

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды