Mitsubishi Electric MSY-GL-NA Series Скачать руководство пользователя страница 41

Страница: 41 / 76

10 TROUBLESHOOTING

10-1. CAUTIONS ON TROUBLESHOOTING

1. Before troubleshooting, check the following

1) Check the power supply voltage.

2) Check the indoor/outdoor connecting wire for miswiring.

2. Take care of the following during servicing

1) Before servicing the air conditioner, be sure to turn OFF the main unit first with the remote controller, then after con-

firming the horizontal vane is closed, turn off the breaker and/or disconnect the power plug.

2) Be sure to turn OFF the power supply before removing the front panel, the cabinet, the top panel, and the electronic

control P.C. board.

3) When removing the electrical parts, be careful of the residual voltage of smoothing capacitor.

4) When removing the electronic control P.C. board, hold the edge of the board with care NOT to apply stress on the

components.

5) When connecting or disconnecting the connectors, hold the connector housing. DO NOT pull the lead wires.

3. Troubleshooting procedure

1) Check if the OPERATION INDICATOR lamp on the indoor unit is blinking on and off to indicate an abnormality. To make

sure, check how many times the OPERATION INDICATOR lamp is blinking on and off before starting service work. (See

the service manual of the indoor unit for a description of those failure codes.)

2) Before servicing, verify that all connectors and terminals are connected properly.

3) When the electronic control P.C. board seems to be defective, check for disconnection of the copper foil pattern and

burnt or discolored components.

4) Refer to 10-2 and 10-3.

Lead wiring

Connector housing

MUZ-GL09NA MUZ-GL09NAH MUY-GL09NA

MUZ-GL12NA MUZ-GL12NAH MUY-GL12NA

MUZ-GL15NA MUZ-GL15NAH MUY-GL15NA

MUZ-GL18NA MUZ-GL18NAH MUY-GL18NA

MUZ-GL24NA MUZ-GL24NAH MUY-GL24NA

OBH733J

Содержание MSY-GL-NA Series













































































Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды

Mitsubishi Electric MSY-GL-NA Series, Руководство по обслуживанию

Результаты поиска

Содержание MSY-GL-NA Series

Отзывы:

Похожие инструкции для MSY-GL-NA Series

Бренды по названию

Популярные бренды