manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Руководство по техническому обслуживанию

Поделиться
Скачать
Mitsubishi Electric MSC-CA20VB Скачать руководство пользователя страница 91

91

6-18. OUTDOOR FAN MOTOR CONTROL

Fan speed is switched according to the compressor frequency.

COOL

Fan speed

Up

Down

Up

Down

Mode

HEAT

Compressor frequency

MUZ-GA50/GA60

MUZ-GA71

<Relation between compressor frequency and fan speed>

54Hz

39Hz

54Hz

39Hz

44Hz

33Hz

44Hz

33Hz

Up

Down

Fan speed

High

Low

Compressor frequency

Min.

Max.

(3) Positioning

The vane presses the vane stopper once to confirm the standard position and then moves to the set angle.
Confirming of standard position is performed in case of follows.
(a) When the power supply turns ON.
(b) When the operation starts or finishes (including timer operation).
(c) When the test run starts.
(d) When multi-standby starts or finishes.

(4) VANE AUTO (

) mode

The microprocessor automatically determines the horizontal vane angle and operation to make the optimum room tem-
perature distribution.

COOL and DRY operation
Vane angle is fixed to Angle 1.

HEAT operation
Vane angle is fixed to Angle 4.

(5) STOP (operation OFF) and ON-TIMER standby

When the following cases occur, the horizontal vane returns to the closed position.
(a) When OPERATE/STOP (ON/OFF) button is pressed (POWER OFF).
(b) When the operation is stopped by the emergency operation.
(c) When ON-TIMER is ON standby.

(6) Dew prevention

During COOL or DRY operation with the vane angle at Angle 4 or 5 when the compressor cumulative operation time
exceeds 1 hour, the vane angle automatically changes to Angle 1 for dew prevention.

6-19. AUTO VANE OPERATION

1. Horizontal vane
(1) Vane motor drive

These models are equipped with a stepping motor for the horizontal vane. The rotating direction, speed, and angle of
the motor are controlled by pulse signals (approx. 12V) transmitted from indoor microprocessor.

(2) The horizontal vane angle and mode changes as follows by pressing VANE CONTROL button.

OBT06D--4qxp  07.3.2 9:53 AM  Page 91

Содержание MSC-CA20VB





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды