manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Руководство по техническому обслуживанию

Поделиться
Скачать
Mitsubishi Electric MSC-CA20VB Скачать руководство пользователя страница 119

119

Time chart of defrosting in HEAT mode (reverse type)

set position

set speed

set position

set speed

Indoor fan (upper)

Compressor normal

Outdoor fan

R.V. coil 

(21S4)

OFF (COOL)

OFF

Maximum frequency

vertical

Horizontal vane

Very Low (temperature of indoor coil thermistor > 18

:

)

30

seconds

30

seconds

30

seconds

40

seconds

5 seconds

5 seconds

40

seconds

OFF

OFF

OFF

ON (HEAT)

ON

ON

ON (HEAT)

Damper

Indoor fan (lower)

OFF

CLOSE

ON

ON

OPEN or CLOSE

OPEN or CLOSE

NOTE : When the air outlet selection switch is set to blow out air from the upper air outlet only, the damper 
             is closed and the lower fan motor is OFF at all times.

<outdoor unit>

<indoor unit>

9-4. AUTO CHANGE OVER ··· AUTO MODE OPERATION

Once desired temperature is set, unit operation is switched automatically between COOL and HEAT operation.

1. Mode selection

(1) Initial mode

At first indoor unit operates only indoor fan with outdoor unit OFF for 3 minutes to detect present room temperature.
Following the conditions below, operation mode is selected. 

1

If the room temperature thermistor RT11 reads more than set temperature, COOL mode is selected. 

2

If the room temperature thermistor RT11 reads set temperature or less, HEAT mode is selected.

(2) Mode change

In case of the following conditions the operation mode is changed.

1

COOL mode changes to HEAT mode when 15 minutes have passed with the room temperature 2 degrees below the 
set temperature.

2

HEAT mode changes to COOL mode when 15 minutes have passed with the room temperature 2 degrees above the 
set temperature.

In the other cases than the above conditions, the present operation mode is continued.

NOTE1: Mode selection is performed when multi standby (refer to NOTE2) is released and the unit starts operation with 

ON-timer.

NOTE2: If two or more indoor units are operating in multi system, there might be a case that the indoor unit, which is 

operating in AUTO (     ), cannot change over the other operating mode (COOL

HEAT) and becomes a        

state of standby.

(3) Indoor fan control/ Vane control

As the indoor fan speed and the horizontal vane position depend on the selected operation mode, when the operation
mode changes over, they change to the exclusive ones. 

OBT06D--4qxp  07.3.2 9:53 AM  Page 119

Содержание MSC-CA20VB





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды