manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Руководство по техническому обслуживанию

Поделиться
Скачать
Mitsubishi Electric MSC-CA20VB Скачать руководство пользователя страница 72

72

MSZ-GA • MSZ-CB MICROPROCESSOR CONTROL

6

Once the operation mode is set, the same operation mode can be repeated by simply turning OPERATE/STOP
(ON/OFF) button ON.
Indoor unit receives the signal with a beep tone.
When the system turns off, 3-minute time delay will operate to protect system from overload and compressor will not
restart for 3 minutes.

WIRELESS REMOTE CONTROLLER

ON-TIMER button

CLOCK SET button

TIME SET buttons
FORWARD button
BACKWARD button

OFF-TIMER button

 

(This diagram shows an overall view.)

RESET button

VANE CONTROL button

Signal transmitting section

Operation display section

Temperature buttons

OPERATE/STOP
 (ON/OFF) button

FAN SPEED CONTROL button

OPERATION SELECT button

ECONO COOL button

Indication of 
remote controller
model is on back

MSZ-GA22VA MSZ-CB22VA
MSZ-GA25VA MSZ-CB25VA MUZ-GA25VA MUZ-GA25VAH
MSZ-GA35VA MSZ-CB35VA MUZ-GA35VA MUZ-GA35VAH

Operation Indicator lamp
The operation indicator at the right side of the indoor unit indicates the operation state.

Approx.
2 

: 

or more

Difference 
between target
temperature 
and room 
temperature

Approx.
2 

: 

or less

This shows that the 
air conditioner is 
operating to reach 
the target temperature.
Please wait until the 
target temperature is 
obtained.

This shows that the 
room temperature is 
approaching the 
target temperature.

Operation state

Indication

Lighted

Not lighted

•The following indication applies regardless of shape of the indicator.

Operation Indicator

INDOOR UNIT DISPLAY SECTION

OBT06D--3qxp  07.3.2 9:42 AM  Page 72

Содержание MSC-CA20VB





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды