manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Руководство по техническому обслуживанию

Поделиться
Скачать
Mitsubishi Electric MSC-CA20VB Скачать руководство пользователя страница 162

162

1. Pre-heat control is turned ON for 15 or 30 min

w

after the breaker is turned ON.

2. 30 min. after the unit is stopped, pre-heat control is turned ON for 15 or 30 min.

w

and turned OFF for 30 min.  

This is repeated as shown in the graph until the breaker is turned OFF.

w

When outside temperature is 20

:

or below , pre-heat control is ON for 30 min.

When outside temperature is 21

:

or above, pre-heat control is ON for 15 min.

NOTE: When the unit is started with the remote controller, pre-heat control is turned OFF.

Compressor uses 50W when pre-heat control is turned ON.

12-8. PRE-HEAT CONTROL

MXZ-2A MXZ-4A80VA

-

MXZ-5A

E2

Power

ON
OFF

Compressor

ON
OFF

Outside temperature

30min.

30min.

30min.

30min.

30min.

30min.

15min. 30min. 15min. 30min.

Pre-heat

ON
OFF

Breaker ON

20

:

Stop
operation

Start
operation

When outside
temperature is
above 20

:

The compressor is energized even while it is not operating. 
This is to generate heat at the winding to improve the compressor's start-up condition.

12-9. COOL OPERATION

2. Coil frost prevention

The compressor operational frequency is controlled to prevent the indoor heat exchanger temperature from falling
excessively.
Compressor is turned OFF for 5 minutes when temperature of indoor coil thermistor continues 3: or less for 5 min-
utes or more.

1. Thermostat control

Thermostat is ON or OFF by difference between room temperature and set temperature.

ON                                   -1 

:

or more

OFF                                 less than -1 

:

-1

:

-0.7

:

Room temperature minus 
set temperature (During operation)

Room temperature minus 
set temperature (Initial)

Thermostat 

OBT06D--6qxp  07.3.2 10:16 AM  Page 162

Содержание MSC-CA20VB





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды