13
4. Timer
Ŷ
Timer functions are different by each remote controller.
Ŷ
For details on how to operate the remote controller, refer to the appropriate operation manual included with each remote controller.
Notes:
Any person at the following places cannot be detected.
Ɣ $ORQJWKHZDOORQZKLFKWKHDLUFRQGLWLRQHULVLQVWDOOHG
Ɣ 'LUHFWO\XQGHUWKHDLUFRQGLWLRQHU
Ɣ :KHUHDQ\REVWDFOHVXFKDVIXUQLWXUHLVEHWZHHQWKHSHUVRQDQG
the air conditioner
A person may not be detected in the following situations.
Ɣ 5RRPWHPSHUDWXUHLVKLJK
Ɣ $SHUVRQZHDUVKHDY\FORWKHVDQGKLVKHUVNLQLVQRWH[SRVHG
Ɣ $KHDWLQJHOHPHQWRIZKLFKWHPSHUDWXUHFKDQJHVVLJQL¿FDQWO\LV
present.
Ɣ 6RPHKHDWVRXUFHVVXFKDVDVPDOOFKLOGRUSHWPD\QRWEHVHQVHG
Ɣ $KHDWVRXUFHGRHVQRWPRYHIRUDORQJWLPH
The 3D i-See sensor operates once approximately every 3 minutes
WRPHDVXUHWKHÀRRUWHPSHUDWXUHDQGGHWHFWSHUVRQVLQWKHURRP
Ɣ 7KHLQWHUPLWWHQWRSHUDWLQJVRXQGLVDQRUPDOVRXQGSURGXFHGZKHQ
the 3D i-See sensor is moving.
Ɣ :KHQ0$5HPRWH&RQWUROOHULVXVHGWRFRQWUROPXOWLSOHUHIULJHUDQW
systems, No occupancy Auto-OFF cannot be used.
3. Operation
1
Select the setting with the [F4]
button.
2)) ĺ &RROLQJ RQO\ ĺ +HDWLQJ
RQO\ĺ&HDWLQJĺ2))«
After changing the setting, press
the [SELECT] button to save the
setting.
OFF: The function is disabled.
Cooling only: When the thermostat
turns off during cooling mode, the
vanes move up and down.
Heating only: When the thermostat
turns off during heating mode,
the vanes move to the horizontal
DLUÀRZGLUHFWLRQWRFLUFXODWHWKHDLU
Cooling/Heating: The function is
enabled during both cooling mode
and heating mode.
* In order to enable this function,
WKH DLUÀRZ GLUHFWLRQ PXVW EH VHW
to “Auto”.
6HDVRQDODLUÀRZIXQFWLRQ
F1
F2
F3
F4
Seasonal airflow
Select:
Seasonal airflow
Cooling/Heating
B
A
D
C
:HHNO\VFKHGXOH:LUHOHVVUHPRWHFRQWUROOHU
Ŷ 7KHZHHNO\VFKHGXOHFDQEHVHWWRIRXURSHUDWLRQSDWWHUQVIRUHDFKGD\RIWKHZHHN7KHVHWWLQJVLQFOXGHWKH
on and off times and the set temperature.
<Editing mode>
1. Switching to the editing mode
1
Press the
button when the unit is operating or stopped.
blinks. (Fig. 1)
2. Selecting the setting pattern
1
Press the
button to select the setting pattern number.
Each time the
button is pressed, the pattern number
A
FKDQJHVLQWKHIROORZLQJRUGHUĺĺĺ
3. Selecting the day of the week
1
Press the
button to select the day of the week to set.
Each time the
button is pressed, the day of the week
B
FKDQJHVLQWKHIROORZLQJRUGHU0RQĺ7XH
ĺ:HGĺ7KXĺ)ULĺ6DWĺ6XQĺ$OOGD\V
4. Selecting the operation settings
1
Push the
button to select the operation on or off setting. (Fig. 2)
(
) is lighted.
Each time the
button is pressed, the setting changes in the following order:
ĺ
.
2
Press the
button to select the operation time. (Fig. 3)
The operation time blinks.
Set the operation time using the
buttons.
7KHRSHUDWLRQWLPHFDQEHVHWLQPLQXWHLQFUHPHQWV
3
Push the
button to select the set temperature. (Fig. 4)
The set temperature blinks.
Set the temperature using the
buttons.
:KHQVHWWLQJWKHRIIRSHUDWLRQWKHWHPSHUDWXUHFDQQRWEHVHW
When the AUTO (dual set point) mode is enabled, press the
button to switch between the upper limit
C
and the lower limit
D
. (Fig. 5)
4
By pressing the
button, the pattern number settings for the displayed day of the week are deleted.
5
Repeat steps 2–4 to select the settings for each day of the week.
<Transmitting the settings>
Point the transmission area of the wireless remote controller towards the receiver on the indoor unit and operate
WKHFRQWUROOHU&RQ¿UPWKDWWKHLQGRRUXQLWEHHSVWLPHV
Press the
button.
<Enabling the weekly schedule>
Press the
button.
The weekly schedule operates when
is on.
7KHZHHNO\VFKHGXOHGRHVQRWIXQFWLRQZKHQWKH2Q2IIWLPHULVHQDEOHG
The weekly schedule operates when all of the On/Off timer settings have been executed.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 1
BH79A366H01_en.indd 13
11/28/2017 1:31:19 PM
