11
3. Operation
Vane setting
Direct
Indirect
Cooling
KRUL]RQWDOĺVZLQJ
keep horizontal
Heating
keep downward
GRZQZDUGĺKRUL]RQWDO
Ŷ
&RQ¿UPDWLRQSURFHGXUH
F1
F2
F3
F4
Manual vane angle
Input display:
Cur.
Address
Check
Ref. address
Unit No.
Identify unit Check button
F1
F2
F3
F4
Manual vane angle
Return:
Ref. address
Unit No.
Function setting for unit
with vane fully open.
F1
F2
F3
F4
Manual vane angle
Return:
No communication
Check Unit state.
3.6. 3D i-See sensor setting
3.6.1 3D i-See sensor setting
F1
F2
F3
F4
Main
Main display:
Cursor
Page
Main menu
Maintenance
Initial setting
Service
F1
F2
F3
F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
3D i-See sensor
1
First, confirm by setting “Ref.
address” to 0 and “Unit No.” to 1.
0RYHWKHFXUVRUWR³5HIDGGUHVV´
or “Unit No.” with the [F1] button to
select.
6HOHFWWKHUHIULJHUDQWDGGUHVVDQG
the unit number for the units to
ZKRVHYDQHVDUHWREH¿[HGZLWK
the [F2] or [F3] button, and press
the [SELECT] button.
5HIDGGUHVV5HIULJHUDQWDGGUHVV
8QLW1R
3UHVVWKH>)@EXWWRQWRFRQ¿UPWKH
unit.
2
Change the “Unit No.” in order and
check each unit.
3UHVVWKH>)@EXWWRQWRVHOHFW³8QLW
No.”.
Press the [F2] or [F3] button to
change the “Unit No.” to the unit
that you want to check, and then
press the [F4] button.
$IWHUSUHVVLQJWKH>)@EXWWRQZDLW
approximately 15 seconds, and
then check the current state of the
air conditioner.
ĺ7KHYDQHLVSRLQWLQJGRZQZDUG
ĺ7KLVDLUFRQGLWLRQHULVGLVSOD\HG
on the remote controller.
ĺ$OORXWOHWVDUHFORVHGĺ3UHVV
the [RETURN] button and continue
the operation from the beginning.
ĺ7KHPHVVDJHVVKRZQWRWKHOHIW
DUHGLVSOD\HGĺ7KHWDUJHWGHYLFH
does not exist at this refrigerant
address.
3UHVV WKH >5(7851@ EXWWRQ WR
return to the initial screen.
3
Change the “Ref. address” to the
next number.
5HIHUWRVWHS
1
to change the “Ref.
address” and continue with the
FRQ¿UPDWLRQ
1
Select “Maintenance” from the
Main menu (refer to page 8), and
press the [SELECT] button.
2
Select “3D i-See sensor” with the
[F1] or [F2] button, and press the
[SELECT] button.
F1
F2
F3
F4
3D i-See sensor
Cursor
Setting display:
Air distribution
Energy saving option
Seasonal airflow
3.6.2 Air
distribution
F1
F2
F3
F4
Air distribution
Input display:
Cur.
Address
Check
Ref. address
Unit No.
Identify unit Check button
F1
F2
F3
F4
Air distribution
Select:
Cur.
Ref. address
Unit No.
Auto vane
Direct/Indirect setting
All
Direct/Indirect
3
Select the desired menu with the
[F1] or [F2] button, and press the
[SELECT] button.
$LUGLVWULEXWLRQ
6HOHFWWKHDLUÀRZGLUHFWLRQFRQWURO
PHWKRGZKHQWKHDLUÀRZGLUHFWLRQ
is set to “Auto”.
(QHUJ\VDYLQJRSWLRQ
Operates the energy-save mode
according to whether persons are
detected in the room by the 3D
i-See sensor.
6HDVRQDODLUÀRZ
When the thermostat turns off, the
fan and the vanes operate accord-
ing to the control settings.
1
Move the cursor to “Ref. address”
or “Unit No.” with the [F1] button to
select.
Select the refrigerant address and
the unit number for the units to
ZKRVHYDQHVDUHWREH¿[HGZLWK
the [F2] or [F3] button, and press
the [SELECT] button.
5HIDGGUHVV5HIULJHUDQWDGGUHVV
8QLW1R
3UHVVWKH>)@EXWWRQWRFRQ¿UPWKH
unit.
The vane of only the target indoor
unit is pointing downward.
2
Select the menu with the [F4] but-
ton.
'HIDXOWĺ$UHDĺ'LUHFW,QGLUHFW
ĺ'HIDXOW«
Default: The vanes move the same
as during normal operation.
During cooling mode, all of the
vanes move to the horizontal air-
ÀRZGLUHFWLRQ
During heating mode, all of the
YDQHV PRYH WR WKH GRZQ DLUÀRZ
direction.
Area: The vanes move to the down
DLUÀRZGLUHFWLRQWRZDUGDUHDVZLWK
a high floor temperature during
cooling mode and toward areas
ZLWKDORZÀRRUWHPSHUDWXUHGXU
-
ing heating mode. Otherwise,
the vanes move to the horizontal
DLUÀRZGLUHFWLRQ
Direct/Indirect: The vanes auto-
matically move relative to the areas
where persons are detected.
The vanes operate as indicated in
the following table.
BH79A366H01_en.indd 11
11/28/2017 1:31:18 PM
