Mitsubishi Electric melfa RV-5AS Скачать руководство пользователя страница 14

Страница: 14 / 56

2-8

Installation

2 Unpacking to Installation

2.2.3 Installation procedures

The installation procedure of the robot arm is shown below.

Fig.2-2: Installation dimensions

1) The base of the robot has already been machined flat. There are four installation holes (

9) on the

base of the robot. Secure the robot into place using these holes with the included parts below. (Recom-
mended tightening torque: 26.5 N•m)

• Installation screws (M8 hex socket screws)
• Spring washers for installation screws
• Plain washers for installation screws

2) Install the robot on a level surface.
3) It is recommended that the surface roughness of the table onto which the robot is to be installed by 6.3

Ra or more. If the installation surface is rough, the contact with the table will be poor, and positional
deviation could occur when the robot moves.

4) When installing, use a common table to prevent the position of the devices and jigs subject to robot

work from deviating.

5) The installation surface must have sufficient strength to withstand the arm reaction during operation,

and resistance against deformation and vibration caused by the static (dynamic) load of the robot arm
and peripheral devices, etc.

6) The installation surface must have sufficient strength to withstand the arm reaction during moving the

robot at high speed.

Installation bolt: 4-M8×35

Spring washer

Plain washer

installation hole

(Installation)

Bottom view: Installation dimensions

Ra6.3

217

67.5

(135)

(80)

67.5

Ra6.3

(21

(135)

(80)

Содержание melfa RV-5AS

























































Результаты поиска

Содержание melfa RV-5AS

Отзывы:

Похожие инструкции для melfa RV-5AS

Бренды по названию

Популярные бренды

Mitsubishi Electric melfa RV-5AS, Инструкция по эксплуатации

Результаты поиска

Содержание melfa RV-5AS

Отзывы:

Похожие инструкции для melfa RV-5AS

Бренды по названию

Популярные бренды