TA7102 Hardware Installation
23
153/1531-ANF 901 14 B 2017-03-08
Default Static IPv4 Address Configuration
If there is no DHCP server in your network, then the IP address has to be configured statically.
To start the TA7102 with a static IP address:
1. With a 10/100 Hub and two 10/100 BaseT Ethernet RJ-45 straight cables, connect both cables to the
Hub; one of them is connected into the
WAN
connector. The other cable links the computer to the
Hub.
2. Reconfigure the IP address of your computer to
192.168.0.11
and the Subnet Mask to
255.255.255.0
.
3. Restart the computer.
4. Power on the TA7102, by connecting the other end of the power cord to an electrical outlet. The
electrical outlet must be installed near the TA7102 so that it is easily accessible.
5. Insert a small, unbent paper clip into the
Reset / Default
hole located at the rear of the TA7102. The
Power
LED will start blinking, and after a few seconds, all the LEDS will start blinking. Release the
paper clip after all the LEDs start blinking and before they all stop blinking (between 7-11 seconds).
This procedure is called a partial reset. After a partial reset is performed, the TA7102 uses the
default IP address 192.168.0.1/24. Refer to
“Partial Reset” for details on the partial reset procedure.
The corresponding link-local IPv6 address is also available and printed on the sticker under the
TA7102.
You can now access the TA7102 web interface. Refer to the
Software Configuration Guide
for more
details.
IPv6 Link Local Address Configuration
If there is no DHCPv6 server or IPv6 router in your network, you can use the link local address to contact
the unit. Note that the TA7102 IPv6 interface is disabled by default.
1. With a 10/100 Hub and two 10/100 BaseT Ethernet RJ-45 straight cables, connect both cables to the
Hub; one of them is connected into the
WAN
connector. The other cable links the computer to the
Hub.
2. Power on the TA7102 by connecting the other end of the power cord to an electrical outlet. The
electrical outlet must be installed near the TA7102 so that it is easily accessible.
3. Insert a small, unbent paper clip into the
Reset / Default
hole located at the rear of the TA7102. The
Power
LED will start blinking, and after a few seconds, all the LEDS will start blinking. Release the
paper clip after all the LEDs start blinking and before they all stop blinking (between 7-11 seconds).
This procedure is called a partial reset. After a partial reset is performed, the TA7102 enables its link
local IPv6 address. Refer to
Partial Reset
for details on the partial reset procedure. The
corresponding link-local IPv6 address is also available and printed on the sticker under the TA7102.
Proceed with accessing the TA7102’s web interface by using the unit’s link local address. The unit’s link
local address is printed on a sticker under the unit. The link local address can be determined by using the
following pattern: [fe80::290:f8ff:feXX:XXXX] where XXXXXX are the last 6 digits of the unit’s MAC
address. Example: The link local address for the TA7102 with MAC address 00:90:F8:12:34:56 would be
[fe80
::290:f8ff:fe12:3456]
.
Содержание TA7102
Страница 1: ...Mitel TA7102 INSTALLATION GUIDE...
Страница 12: ...TA7102 Hardware Installation 12 153 1531 ANF 901 14 B 2017 03 08 5 Power connector External 12 Vdc power supply...
Страница 43: ...TA7102 Hardware Installation 43 153 1531 ANF 901 14 B 2017 03 08 QoS ToS DiffServ 802 1p 802 1Q...
Страница 53: ...TA7102 Hardware Installation 153 1531 ANF 901 14 B 2017 03 08 53...
