manualshive.com logo in svg

Minebea MPC-201-25, Инструкция по эксплуатации

Поделиться
Скачать
Minebea MPC-201-25 Скачать руководство пользователя страница 8

 

 

VI

 

Do not open numerical data or alarm history csv files while acquiring data with the PC. 
Opening such files while acquiring data with the PC will result in an error, and will turn the PC interface 
off-line without updating the numerical data or alarm history.

 

Set the start trigger signal interrupt interval to at least 1 s.

 

 

Leave an interval of at least 1 s before starting measurement after changing the conditions or aborting 
measurement using the [Stop] button. 

 

Always make sure that the latest version of the measurement software is installed and used. Older 
versions of the software will not operate with the latest version of the amplifier updated with additional 
features. 
The latest software version supports all previous amplifiers. 

 

When upgrading the measurement software, always uninstall the old software version first before 
installing the new version. 

 

For details on how to attach the sensor to the mold, see Section 25 "Appendix". 

 

 

 

Содержание MPC-201-25





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды