Minebea MPC-201-25 Скачать руководство пользователя страница 110

Страница: 110 / 124

21. Troubleshooting

Check the corresponding reference details if any of the following problems arise when using the
module.
If the particular problem is not listed here or if the problem is not remedied by the corrective action
suggested, contact us.

21-1.

General

Symptom Check

points

Reference

section

The relay box cannot be
mounted securely.

Does the magnetic sheet provide sufficient attraction?
If necessary, attach the mounting plates, and mount using
screws.

Section 1. (3)

(beginning)

The LEDs do not
illuminate.

Is the power supply voltage within the permissible range?
24 V DC, (permissible range: 20.4 V ~ 27.6 V DC)

Section

5-2-1.

Is the power supply cable correctly connected?

Section

5-2-1.

The module switches to
offline mode when the
software is launched.

Is the module power turned on?

―

Is the USB cable connected?

―

Has the USB driver for the module been installed?

Section 5-4.

The pressure waveform is
not plotted.

Are sensors connected to the channels enabled?

―

Are the sensor connectors inserted fully?

Section

5-2-5.

Are the sensor inputs normal?
Check the sensor inputs on the Monitor screen.

Section 15.

The ERROR status LED
is illuminated.

An error has occurred in the amplifier unit. Connect to a PC
with the ERROR LED illuminated to check the error details.
(ROM Ver.1.014 or later)

Section 17.

21-5.

An overload (+OL, -OL)
error has occurred.

Is an unused channel enabled with no sensor connected?

Section

9-1-2.

USB communication is
unstable.

Is the dedicated USB cable provided being used?

―

Has the ferrite core provided with the USB cable been
attached correctly?

Section

5-2-4.

Is the equipment being used correctly?
Has it been grounded?

Section 4.

Cannot read the
configuration file.

Is the amplifier software the latest version?
Some newer configuration files cannot be read with older
amplifier software versions.

―

Содержание MPC-201-25





























































































































Результаты поиска

Содержание MPC-201-25

Отзывы:

Бренды по названию

Популярные бренды

Minebea MPC-201-25, Инструкция по эксплуатации

Результаты поиска

Содержание MPC-201-25

Отзывы:

Бренды по названию

Популярные бренды