Minebea MPC-201-25 Скачать руководство пользователя страница 103

Страница: 103 / 124

(4) STEP 4: Fine adjustment complete

Fine adjustment of the analog output is now complete for the channel specified.
*

Note that the adjustment procedure is not yet complete at this stage. To end adjustment and
save the settings in the module, click [Register].

Button name

Description

[Adjust other channel]

To continue and fine-adjust another channel, click this button.
The display switches to the channel selection screen.
*The settings already adjusted here are stored temporarily.
The adjustment procedure is not completed until [Register] is
clicked.

[Back]

Returns to the previous screen.

[Register]

Enters the adjustment settings for all channels for which
analog output was fine-adjusted, and completes the
adjustment procedure.

[Cancel]

Discards the adjustment settings and aborts adjustment.
*The settings are returned to their respective values before
analog fine adjustment.

Содержание MPC-201-25





























































































































Результаты поиска

Содержание MPC-201-25

Отзывы:

Minebea MPC-201-25, Инструкция по эксплуатации, Страница: 103 / 124

Результаты поиска

Содержание MPC-201-25

Отзывы: