Miller DYNASTY 200 DX Скачать руководство пользователя страница 42

Страница: 42 / 92

OM-2240 Page 36

Changing Programmable TIG Start Polarity (Dynasty Models Only)

SEL E−

Amperage Switch Pad

Encoder Control

Amps Meter

To adjust TIG Start Polarity proceed as

follows:
Press Amperage switch pad. Switch pad

LED turns on, and meter % LED turns on.

The current Start Polarity,

(SEL]

[E−]

[SEL]

[EP]

is displayed on meters, and can be

adjusted (see Section 5-16) by turning

the Encoder control.
To change Start Amperage, proceed to

Section C.

Changing Programmable TIG Start Amperage (All Models)

Amperage Switch Pad

Encoder Control

Amps Meter

To adjust TIG Start Amperage proceed

as follows:
Press Amperage switch pad. Switch pad

LED turns on, and meter A LED turns on.

The current Start Amperage is displayed

on the amps meter, and can be adjusted

(see Section 5-16) by turning the

Encoder control.
To change Start Time, proceed to Section

SEL 20

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды