Miller DYNASTY 200 DX Скачать руководство пользователя страница 70

Страница: 70 / 92

Om-2240 Page 64

11-3. Lift-Arc

™

And HF TIG Start Procedures

Lift-Arc Start

When Lift-Arc

button light is On,

start arc as follows:
1

TIG Electrode

Workpiece

Touch tungsten electrode to work-

piece at weld start point, enable out-

put and shielding gas with torch trig-

ger, foot control, or hand control.

Hold electrode to workpiece for

1-2 seconds

, and slowly lift elec-

trode. Arc is formed when electrode

is lifted.
Normal open-circuit voltage is not

present before tungsten electrode

touches workpiece; only a low

sensing voltage is present between

electrode and workpiece. The

solid-state output contactor does

not energize until after electrode is

touching workpiece. This allows

electrode to touch workpiece with-

out overheating, sticking, or getting

contaminated.

Application:

Lift-Arc is used for the DCEN or AC

GTAW process when HF Start

method is not permitted, or to re-

place the scratch method.

HF Start

When HF Start button light is On,

start arc as follows:
High frequency turns on to help

start arc when output is enabled.

High frequency turns off when arc is

started, and turns on whenever arc

is broken to help restart arc.

Application:

HF start is used for the DCEN

GTAW process when a non-con-

tact arc starting method is required.

−

Seconds

“Touch”

Do NOT Strike Like A Match!

Lift-Arc Start Method

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды