Miller DYNASTY 200 DX Скачать руководство пользователя страница 53

Страница: 53 / 92

OM-2240 Page 47

3T Specific Trigger Method (DX, LX And All CE Models)

3T (Specific Trigger Operation)

Sequencer is required to reconfigure for 3T.
3T requires two independent momentary-

contact switches. One will be designated ini-

tial switch, and it must be connected between

Remote 14 receptacle pins A and B. The sec-

ond will be designated as the final switch, and

it must be connected between Remote 14 re-

ceptacle pins D and E.
Select 3T according to Section 6-2C.

Definitions:
Initial slope rate

is the rate of amperage

change determined by the initial amperage,

initial slope time, and main amperage.

Final slope rate

is the rate of amperage

change determined by the main amperage, fi-

nal slope time, and final amperage.

Operation:
A..

Press and release initial switch within 3/4

second to start shielding gas flow. To stop

the preflow sequence before preflow time

elapses (25 seconds), press and release

final switch. The preflow timer will reset

and the weld sequence can be started

again.

If an initial switch closure is not made
again before preflow time ends, gas flow

stops, the timer resets, and an initial

switch press and release is necessary to

start the weld sequence again.

B..

Press initial switch to start arc at initial

amps. Holding switch will change amper-

age at initial slope rate (release switch to

weld at desired amperage level).

C..

When main amperage level is reached,

initial switch can be released.

D..

Press and hold the final switch to de-

crease amperage at final slope rate (re-

lease switch to weld at desired amperage

level).

E..

When final amperage has been reached,

the arc extinguishes and shielding gas

flows for the time set on the Postflow con-

trol.

Application:

With the use of two remote switches instead

of potentiometers, 3T gives the operator the

ability to infinitely increase, decrease, or

pause and hold amperage within the range

determined by the initial, main, and final am-

perages.

SEL

H-3

Current (A)

Remote Trigger Operation

Preflow

Initial Amps/Initial Slope

Main Amps

Final Slope /Final Amps

Postflow

* Arc can be extinguished at any time by pressing and releasing both initial and final switches, or by lifting the torch and breaking the arc.

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды