Miller DYNASTY 200 DX Скачать руководство пользователя страница 58

Страница: 58 / 92

OM-2240 Page 52

6-5. Setting Unit To Display PPP While Pulse Welding (DX And LX Models Only)

Output Switch Pad

Pulser Switch Pad

Power Switch

To access the PPP while welding dis-

play, turn power switch on, and then

press the Output and Pulser switch

pads before the software version

clears the meters. Hold the switch pads

until

[SEL] [−−−]

[SEL] [PPP]

appears.

Encoder Control

PPP Meter Display

Turn Encoder to change between stan-

dard and

(PPP)

meter display.

When the

(PPP)

meter display feature is

active while pulse welding, the

(PPP)

will

be displayed on the right meter display,

and the Meter Hold feature is disabled.
The

(PPP)

meter display feature will not

effect the normal amperage display or

Meter Hold capabilities when in a non-

pulse welding mode.
Press torch trigger or turn off power to

save setting and end this set-up.

− − −

sel

And

PPP

Rear Panel

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды