Miller DYNASTY 200 DX Скачать руководство пользователя страница 55

Страница: 55 / 92

OM-2240 Page 49

6-4. Lockout Functions

A. Accessing Lockout Capability

−

L − −

000

2,3,4

−

L L1

000

And

Rear Panel

See Section 5-1 for explanation of controls referred to in all of

Section 6-4.

There are four (1

−

4) different lockout levels. Each successive level

allows the operator more flexibility.
NOTE: Before activating lockout levels, be sure that all procedures

and parameters are established. Parameter adjustment is limited

while lockout levels are active.
1

Amperage (A) Switch Pad

Adjust Switch Pad

Power Switch

To access lockout screens, turn On power switch, and then before

the software version clears the meters, push and hold the Amperage

and Adjust switch pads until software version number clears meters.
4

Lockout Off

Upon power up as described, the meter % and Amperage (A) switch

pad LED’s light, and the meter display will be as shown for a lockout

off condition.
5

Encoder Control

To turn On the lockout feature, proceed as follows:

Pressing Amperage (A) switch pad will toggle between the meter %

and S LED’s. Toggle switch pad until % LED is on.
Turn Encoder control to select a three digit lockout number. Number

will appear on the voltage (left) meter. Select any number from [

001

]

thru

[

999

IMPORTANT:

remember this three digit number, as you

will need it to turn the lockout feature off.

Toggle Amperage (A) switch pad to light the meter S LED. You may

now select a lockout level.
There are four lockout levels available. Turn Encoder control to se-

lect a lockout level (see Sections B for lockout level descriptions).
6

Lockout On

Once the desired three digits have been entered and a lockout level

selected, press torch trigger or turn Off power to complete lockout on

sequence.
NOTE: Setting a three digit lockout number of [

000

], or setting a lock-

out level of [

L−−

] will cause a lockout off condition.

To turn Off the lockout feature, proceed as follows:

To access lockout screens, turn On power switch, and then before

the software version clears the meters push and hold the Amperage

and Adjust switch pads until software version number clears meters.
Upon power up as described, the meter % and Amperage (A) switch

pad LED’s will turn on, and the meter display will be as shown for a

lockout on (see callout 6) condition.
Use Encoder control to enter the same three digits that were used

to turn on the lockout feature.
Press the Amperage (A) switch pad. The meter % LED will turn off,

and the S LED will light. The amperage (right) meter display will

change to

[

L−−

]

The lockout feature is now off.

Press torch trigger or turn Off power to complete lock out Off

sequence.

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды