Miller DYNASTY 200 DX Скачать руководство пользователя страница 24

Страница: 24 / 92

OM-2240 Page 18

4-6. Weld Output Terminals And Selecting Cable Sizes*

Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit

Not Exceeding

Turn off power before

connecting to weld out-

put terminals.

100 ft (30 m) Or Less

150 ft

(45 m)

200 ft

(60 m)

250 ft

(70 m)

300 ft

(90 m)

350 ft

(105 m)

400 ft

(120 m)

Do not use worn, dam-

aged, undersized, or

poorly spliced cables.

Welding

Amperes***

−

60%

Duty

Cycle

−

100%

Duty

Cycle

−

100% Duty Cycle

100

4 (20)

3 (30)

2 (35)

1 (50)

1/0 (60)

150

3 (30)

2 (35)

1 (50)

1/0 (60)

2/0 (70)

3/0 (95

3/0 (95)

200

3 (30)

2 (35)

1 (50)

1/0 (60)

2/0 (70)

3/0 (95)

4/0 (120) 4/0 (120)

Output Receptacles

−

This chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.

**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.

( ) = mm

for metric use

***Select weld cable size for pulsing application at peak amperage value.

S-0007-E

−

4-7. Remote 14 Receptacle Information

Socket*

Socket Information

15 VOLTS DC

Contactor c15 volts dc.

C L N

D M

15 VOLTS DC

OUTPUT

CONTACTOR

Contact closure to A completes 15 volts dc

contactor control circuit and enables output.

REMOTE

Output to remote control; +10 volts dc output to

remote control.

REMOTE

OUTPUT

CONTROL

Remote control circuit common.

CONTROL

0 to +10 volts dc input command signal from

remote control.

A/V

AMPERAGE

Current feedback; +1 volt dc per 100 amperes.

AMPERAGE

VOLTAGE

Voltage feedback; +1 volt dc per 10 volts output.

803 428-A

GND

+15 volts dc GND

CHASSIS

Chassis common.

*The remaining sockets are not used.
Note: If a remote hand control, like the RHC-14, is connected to the Remote 14 receptacle, some current value above min. must be set on the

remote control before the Panel or Remote contactor is turned on. Failure to do so, will cause current to be controlled by the panel control and

the remote hand control will not function.

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды