Miller DYNASTY 200 DX Скачать руководство пользователя страница 41

Страница: 41 / 92

OM-2240 Page 35

SECTION 6

−

ADVANCED FUNCTIONS

Section 6 in this manual covers operation of all models of 200 and 300 ampere

inverter based TIG machines. Features and options referenced may not be

available on your machine. Verify the model you have before using this section.

NOTE

6-1. Programable TIG Start Parameters

Accessing

Programmable TIG Start Parameters

NOTE

: The welding cycle can be execut-

ed while in programmable start mode.

Before accessing programmable TIG

Start Polarity, Amperage, and Time

modes, be sure that all procedures and

parameters are established.
1

Process Switch Pad

Amperage Switch Pad

Power Switch

To access the programmable TIG Start

Amperage and Time screens, turn power

on, and then press the Process and Am-

perage switch pads before the software

version clears the meters. Hold switch

pads until software version clears the

meters and

[SEL] [EP]

[SEL] [EN]

appears.

Memory Switch Pad (If Equipped)

Press Memory switch pad to select de-

sired memory location (see Section

5-14).

Polarity Switch Pad (If Equipped)

Press Polarity switch pad to select AC or

DC (see Section 5-6).

Note: Each memory location and each

polarity (AC or DC) has its own set of start

parameters.

Press the Process switch pad to select

the desired process, TIG HF Impulse or

TIG Lift Arc, for your application (see

Section 5-7). The parameter values are

the same for both processes, and any

changes made to the values in one pro-

cess, are duplicated in the other process.
6

Output Switch Pad

Press Output switch pad to select de-

sired type of control (see Section 5-8).
Proceed to Section B, C and/or D .
To save changes and exit Advanced

Functions, turn power off.

And

Rear Panel

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды