background image

IMPORTANT SAFETY INSTRUCTIONS

       

 

 

M i g h t y   M u l e   2 0 0

III. After Installation

 

1. 

Attach the 

warning signs

 (included) to each side of the gate to alert the public of auto matic gate 

operation. It is

 

your responsibility to post warning signs on both sides of your gate.  If any of these signs 

or warning decals become damaged, illegible or missing, replace them immediately.  Contact GTO for 

free replacements.

 

2. 

The gate is automatic and could move at any time, posing a serious risk of entrapment.  No one should 

be in contact with an activated gate when it is moving or stationary.

 
 

3. 

Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a 

complete stop.

  4. 

Do not attempt to "beat the gate" while the gate is closing. This is extremely dangerous.

  5.   Do not allow children or pets near your gate.

 Never let children operate or play with gate controls.  

Keep the remote controls away from children and unauthorized users; store controls where children and 

unauthorized users do not have access to them. 

 

6. 

KEEP GATE AND GATE OPENER PROPERLY MAINTAINED. 

Always turn power to opener OFF before 

performing any maintenance. Regularly grease the gate hinges. Clean the push-pull tube with a soft, dry 

cloth and apply silicone spray to it at least once per month. 

  7.   To operate this equipment safely, YOU must know how to disconnect the opener for manual gate 

operation (see page 1).  If you have read the instructions and still do not understand how to disconnect 

the opener, contact the GTO Service Department.

  8.   Disconnect the opener 

ONLY

 when the power is 

TURNED OFF 

and the gate is 

NOT 

moving.

 

9. 

Make arrangements with local fire and law enforcement for emergency access.

 

10.   Distribute and discuss copies of the 

IMPORTANT SAFETY INSTRUCTIONS 

section of this manual with 

all persons authorized to use your gate. 

 

11.

 

IMPORTANT: Save these safety instructions. Make sure everyone who 

is using or will be around the gate and gate opener are aware of the 

dangers associated with automated gates. In the event you sell the 

property with the gate opener or sell the gate opener, provide a copy 

of these safety instructions to the new owner. 

    Should you lose or misplace this manual, a copy can be obtained by 

downloading one from the Mighty Mule® web site (www.mightymule.

com), by contacting GTO, Inc., at 3121 Hartsfield Road, Tallahassee, 

Florida 32303 or by calling 1-800-543-4283 and requesting a duplicate 

copy. One will be provided to you free of charge.

Содержание 200 E-Z GATE OPENER UL325 SERIES








































Отзывы: