Miele T 8826 WP Скачать руководство пользователя | Manualshive

Страница: 32 / 64

background image

3. Cleaning the fine filter in front of
the heat exchanger unit

Removing

^

Use the yellow lever (supplied) to
open the access panel.

^

Insert the lever in the middle of the
gap and lift it up gently (see arrow)
until the panel opens out at the top.

^

Remove the panel.

^

Turn the lever on the inner cover
downwards to the vertical position.

^

Pull the cover forwards.

^

Remove it by pulling it diagonally
upwards.

^

Pull the fine filter out by the handle.

^

Press the stoppers gently together
and then pull them out of the handle.

^

Pull the handle out of the fine filter.

Cleaning

^

Clean the fine filter thoroughly under
running water.

^

Then squeeze the fine filter
thoroughly.

Cleaning and care

32

«
...
30
31
32
33
34
...
»

Содержание T 8826 WP

































































Отзывы:

Нет отзывов

Похожие инструкции для T 8826 WP

Бренд: Vitek Страницы: 24

Бренд: Comelec Страницы: 6

Бренд: Hoover Страницы: 36

Бренд: Matco Tools Страницы: 2

Бренд: Amana Страницы: 2

Evolution Elite EEE-153

Бренд: Henny Penny Страницы: 80

Бренд: Mediclinics Страницы: 65

Бренд: Modena Страницы: 16

Бренд: GE Страницы: 12

Бренд: GE Страницы: 16

Бренд: GE Страницы: 3

Бренд: GE Страницы: 3

Бренд: GE Страницы: 3

Бренд: GE Страницы: 23

CleanSpeak GTD81ESSJWS

Бренд: GE Страницы: 36

Бренд: GE Страницы: 56

CleanSpeak GTD81ESPJMC

Бренд: GE Страницы: 36

Бренд: GE Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды