Miele T 8826 WP Скачать руководство пользователя

Страница: 24 / 64

Once a programme has started

- changing the programme

You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).

You will need to cancel the current
programme before you can select a
new one.

- cancelling the programme and then
selecting a different programme

Press the

Start/Stop

button.

The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.

If you press the

Start/Stop

button

again during the cooling down
phase,

Finish

will light up in the

display.

Press the

Door

button.

Close the door.

Select another programme and start
it.

- cancelling the programme and then
removing the laundry

Proceed as described in "Adding or
removing laundry after a programme
has started" below.

Switch the dryer off after closing the
door.

Altering Delay start

See "Delay start".

Adding or removing laundry
after a programme has started

Press the

Door

button.

Open the door.

Add or remove items as required.

Close the door.

Press the

Start/Stop

button.

Time remaining

The time left shown in the display may
now vary from the actual drying time.

Changing the programme sequence

Содержание T 8826 WP

































































Результаты поиска

Содержание T 8826 WP

Отзывы:

Похожие инструкции для T 8826 WP

Бренды по названию

Популярные бренды

Miele T 8826 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8826 WP

Отзывы:

Похожие инструкции для T 8826 WP

Бренды по названию

Популярные бренды