Miele T 8826 WP Скачать руководство пользователя страница 14

Страница: 14 / 64

Control panel

Gentle tumble button

Delicate fabrics are dried using
reduced mechanical action.

Drying level button

with indicator lights

Display

See next page.

Delay start button

This button is used for:
- Delaying the start of a programme
- Selecting the duration of the timed

drying

Warm air

and

Cool air

programmes

Buzzer button

An audible tone sounds at the end of
the programme.

Perfect Dry indicator

For all sensor controlled drying
programmes. See next page.

Check lights

See the next page and also
"Cleaning and care", "Problem
solving guide" and "After sales ser-
vice".

Start/Stop button

For starting or cancelling a
programme.
The indicator light flashes while a
programme is being selected and is
then on constantly after the
programme has started.

Programme selector

with indicator lights

Door button

Pressing this button will open the
door even when the tumble dryer is
switched off at the mains.

On/Off button

For switching the dryer on and off.

Operating the tumble dryer

Содержание T 8826 WP

































































Результаты поиска

Содержание T 8826 WP

Отзывы:

Похожие инструкции для T 8826 WP

Бренды по названию

Популярные бренды

Miele T 8826 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8826 WP

Отзывы:

Похожие инструкции для T 8826 WP

Бренды по названию

Популярные бренды