Miele T 8826 WP Скачать руководство пользователя | Manualshive

Страница: 15 / 64

background image

The display shows:

– Programme duration

– Programme stage

Drying
Cooling down
Finish

– Check and fault messages

The following are also selected via
the display:

– Duration of the

Warm air

and

Cool air

programmes

– Delay start

You can select a programme and set
it to start at a later time.
The programme will start
automatically once the delay start
time has a elapsed.

– Programmable functions

Default settings can be altered to
adapt the dryer to different
requirements. See "Programmable
functions" at the end of this booklet
for more details.

Perfect Dry indicator

The Perfect Dry system measures the
residual moisture content in the laundry
in sensor controlled programmes to
ensure perfect drying results.

After a programme has started, the
electronics will estimate the duration of
the programme (time remaining). The

Perfect Dry

indicator will flash while this

is happening.
After a short while, the programme
duration will appear in the display and
the indicator will go out.

The

Perfect Dry

indicator will light up

again when the selected drying level is
reached and remain on until the
programme is finished.

The

Perfect Dry

indicator does not light

up during time controlled programmes:

Woollens, Silks, Cool air, Warm air,
Gentle smoothing.

Programme duration /
Estimated time remaining

The estimated duration (time remaining)
will appear in the display.
The following factors all affect the
estimated time remaining: residual
moisture content after spinning; type of
fabric; size of load; room temperature;
fluctuations in power supply.

The electronics continually assess
conditions in the dryer and adjust the
estimated time remaining for a more
accurate reading. Because of this, the
time displayed can alter during the
course of a programme.
Programmes can also finish earlier than
expected, if, for example, particularly
fine fabrics are being dried, the load is
very small or items were partially dry
beforehand.

Operating the tumble dryer

15

«
...
13
14
15
16
17
...
»

Содержание T 8826 WP

































































Отзывы:

Нет отзывов

Похожие инструкции для T 8826 WP

Бренд: Daewoo Страницы: 20

Бренд: CPG Страницы: 13

Бренд: Sierra Страницы: 25

Бренд: S&P Страницы: 20

Бренд: T3 Страницы: 27

Бренд: Comet Страницы: 32

Бренд: N'DUSTRIO Страницы: 134

Бренд: Asko Страницы: 32

Бренд: SEVERIN Страницы: 56

ExxcelWVD24520GB

Бренд: Bosch Страницы: 64

Бренд: Bosch Страницы: 60

Бренд: Hisense Страницы: 56

Бренд: Hisense Страницы: 60

Бренд: Giles & Posner Страницы: 110

Бренд: Fagor Страницы: 82

Бренд: Hotpoint Ariston Страницы: 24

Бренд: Oster Страницы: 12

Бренд: Wahl Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды