Miele T 8826 WP Скачать руководство пользователя | Manualshive

Страница: 8 / 64

background image

Technical safety

~

Before setting up the tumble dryer, check it for any externally

visible damage.
Do not install or use a damaged tumble dryer.

~

Before connecting the tumble dryer, ensure that the connection

data on the data plate (voltage and frequency) match the mains
electricity supply. If in any doubt, consult a qualified electrician.

~

The electrical safety of this tumble dryer can only be guaranteed

when correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested, and where there is
any doubt, the household wiring system should be inspected by a
qualified electrician. Miele cannot be held liable for the
consequences of an inadequate earthing system (e.g. electric
shock).

~

Do not connect the tumble dryer to the mains electricity supply by

an extension lead. Extension leads do not guarantee the required
safety of the tumble dryer (e.g. danger of overheating).

~

If the electrical connection cable is faulty it must only be replaced

by a Miele approved service technician to protect the user from
danger.

~

Unauthorised repairs could result in unforeseen dangers for the

user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician, otherwise any
subsequent damage will not be covered by the guarantee. Ensure
current is not supplied to the tumble dryer until after maintenance or
repair work has been carried out.

~

Faulty components must only be replaced by genuine Miele

original spare parts. Only when these parts are fitted can the safety
standards of the tumble dryer be guaranteed.

Warning and Safety instructions

8

«
...
6
7
8
9
10
...
»

Содержание T 8826 WP

































































Отзывы:

Нет отзывов

Похожие инструкции для T 8826 WP

Bjorn Axen Tools

Бренд: OBH Nordica Страницы: 24

Бренд: Majestic Appliances Страницы: 29

Бренд: Binatone Страницы: 20

Бренд: R.G.V. Страницы: 40

Бренд: VOX electronics Страницы: 33

DRY CONTROL PLUS

Бренд: SALUPO Страницы: 32

Smart Fryer AF-123544.2

Бренд: emerio Страницы: 35

PRIMOTECQ TW730E

Бренд: FUST Страницы: 60

Бренд: Gourmia Страницы: 20

Бренд: Kleenmaid Страницы: 24

Бренд: Russell Hobbs Страницы: 32

Бренд: Master Chef Страницы: 18

Professional ID-1

Бренд: Andis Страницы: 1

Бренд: Haier Страницы: 64

Бренд: Mediclinics Страницы: 14

Бренд: Haier Страницы: 10

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды