Miele PG 8593 Скачать руководство пользователя страница 24

Страница: 24 / 188

Operation

Symbols in the display



Navigation arrows

If a menu consists of more than two options, two navigation arrows
are shown at the side of the menu options.

Settings 

Language 

Date

Use the



and



arrow buttons on the control panel to navigate

through the menu.

- - - - - -

Dotted line

If a menu contains more than two options, the end of the option list is
marked by a dotted line. The last entry appears above the line, the
first entry below it.



Tick

If there are several options available, the current setting is marked
with a tick



Language 

english (GB)

english (USA)

(



System messages

The



symbol denotes system messages. These give information,

such as e.g. if the level is too low in the supply containers or a
reminder for the next service.

Refill salt

System messages are displayed at the start and end of a program
and have to be confirmed (acknowledged) individually with

or all

together at the end of the program by opening the door. If the



symbol appears in the display during a program, the system
messages can be accessed by pressing and holding the OK button.



Fault messages

In the event of a fault a warning triangle is shown in place of the



symbol. See "Problem solving guide" and "After sales service" for
more information.

Содержание PG 8593





























































































































































































Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды

Miele PG 8593, Руководство по эксплуатации

Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды