Miele PG 8593 Скачать руководство пользователя страница 130

Страница: 130 / 188

Problem solving guide

130

The following guide may help you to find the reason for a fault, and to correct it. You
should, however, note the following:



Repairs may only be carried out by Miele Service.

Repairs and other work by unqualified persons could be dangerous for the user.

To avoid unnecessary service call-outs, check that the fault has not been caused by
incorrect operation when an error message first appears.

Technical faults and messages

Problem

Possible cause and remedy

The display is dark and all
LEDs are out.

The machine is not switched on.



Switch the machine on using the



button.

A breaker is defective or has tripped



Refer to the minimum fuse rating on the data plate.



Reset the trip switch.



If the mains breaker trips again, call Miele Service.

The machine is not plugged in.



Insert the plug.

The machine has switched
itself off.

This is not a fault.
The Auto-Off function switches the machine off
automatically after a pre-set duration to save energy.



Switch the machine on again using the



button.

Next service due on:

This is not a fault.
Miele Service has recommended a date for the next service
visit.



Please contact the Miele Service Department to arrange
a service visit.

Содержание PG 8593





























































































































































































Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды

Miele PG 8593, Руководство по эксплуатации

Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды