Miele PG 8593 Скачать руководство пользователя страница 64

Страница: 64 / 188

Settings



Filter change

The air filter in the drying unit must be replaced regularly with a new
one.

For more information on changing the filter see "Maintenance /
Changing the HEPA filter".

Language



The language set will be used in the display.



Open the menu as follows:

Button





Settings 



Language 

The flag symbol



after the

Settings 

and

Language 

options acts as a guide if a language which you do not understand
has already been set before.

Language 

english (GB)

english (USA)

(

A list will appear in the display with all the languages available. The
currently selected language has a tick



beside it.

The factory default language is set as

english (GB)

. For Canada

select "English (CA)" or "Français (CA)".



Use the



and



arrow buttons to select the language you want.



Press

to save the setting.

The display will change immediately to the language selected.

Содержание PG 8593





























































































































































































Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды

Miele PG 8593, Руководство по эксплуатации

Результаты поиска

Содержание PG 8593

Отзывы:

Похожие инструкции для PG 8593

Бренды по названию

Популярные бренды