Midea MCCDH30A-TA3SL страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 169

background image

Air-cooled modular chiller unit

1

2

Safety protection device

1) Protection for over-high discharge pressure.
2) Protection for over-low suction pressure.
3) Power supply phase sequence protection.
4) Anti-freezing protection in cooling mode.
5) Anti-freezing protection in Winter.
6) Protection for compressor over current.
7) Protection for compressor overload.
8) Outlet and inlet water temperature difference protection.
9) Compressor discharge temperature protection.
10) Water flow cut-off protection.
11) Sensor malfunction protection.
12) Low ambient temperature drive-up protection
13) Low-temperature protection of shell and tube heat

exchanger.

Noise level

dB(A)

67

Operation water temp

℃

Cooling

：

0

～

17

（

Less than 5

℃

must add antifreeze

）

Heating

：

22

～

50

Ambient temp

℃

Cooling

：

-10

～

46 Heating

：

-10

～

21

Note:

Please refer to the water flow volume in the above table strictly to design and install.

All the above data is measured base on the following working condition:

1. Cooling mode: water side fouling factor: 0.086m

2

·℃

/kW, chilled water inlet/outlet: 12

℃

/ 7

℃

, and outdoor ambient temp. of

35

℃

DB.

2. Heating mode: water side fouling factor: 0.086m

2

·℃

/kW, warm water inlet/outlet: 40

℃

/ 45

℃

, and outdoor ambient temp.

7

℃

DB/6

℃

WB.

«
...
10
11
12
13
14
...
»

Содержание MCCDH30A-TA3SL










































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MCCDH30A-TA3SL

Бренд: Salford Страницы: 64

Бренд: Yaros Страницы: 58

Бренд: intensity Страницы: 32

Бренд: Filtrine Страницы: 33

Бренд: Jet Страницы: 12

Бренд: Kaysun Страницы: 118

SkyAir RZF-A Series

Бренд: Daikin Страницы: 213

Bear Car CH45342 (77412)

Бренд: Echo Страницы: 2

Бренд: Echo Страницы: 1

Бренд: Trane Страницы: 24

Бренд: Rabbit Laser USA Страницы: 2

Бренд: MPC Страницы: 38

Бренд: Garland Страницы: 112

Бренд: Jensen Страницы: 132

Бренд: Barko Страницы: 58

Бренд: York Страницы: 216

Бренд: York Страницы: 326

Бренд: Husqvarna Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды