Midea MCCDH30A-TA3SL Скачать руководство пользователя страница 137

Страница: 137 / 169

Air-cooled modular chiller unit

4. INSTALLATION PROCEDURE

Installation procedure:

Use PQE connect with each other when several wired-controllers are parallel.

NOTE

Please connect the attached shorted-wires to the corresponding communication port COM(I) or COM(O) in

the main control board of the last parallel unit (dial code ). Directly connect to the last parallel unit if only one

unit is connected.

The wiring procedure and principles are shown in the figure:

llo

Outdoor electric

control box

Communicate with

upper unit(reserved).

Please use

3-cord shielding

wires for

connection. The

wire length

depends on the

specific situation

in the installa-

tion.

wired controller

5-bit terminal base

5. OVERVIEW OF WIRED CONTROLLER

Basic conditions of operating the wired controller

1). Applicable range of supply voltage: Input voltage is AC 220V±10%, powered to wired controller by

attached power adapter.
2). Operating environment temperature of wired controller: -15

℃

~+46

℃

3). Operating RH of wired controller: RH40%~RH90%.

Содержание MCCDH30A-TA3SL










































































































































































Результаты поиска

Содержание MCCDH30A-TA3SL

Отзывы:

Midea MCCDH30A-TA3SL, Техническое и сервисное руководство, Страница: 137 / 169

Результаты поиска

Содержание MCCDH30A-TA3SL

Отзывы: