microHAM MK2R Скачать руководство пользователя страница 6

Страница: 6 / 80

Other:

•

configurable Accessory connection with dual BCD band data outputs

•

user definable presets to recall all parameters for different control programs or contests

•

all parameters are stored inside the box memory and reloaded after power up

•

integrated chokes and filters for maximum RFI immunity

•

Metal/Aluminum case, powder coated and silk screened

•

Free, no time limit firmware/software upgrades via Internet

2 - IMPORTANT WARNINGS

ALWAYS check the polarity of the 13.8 V power supply.

When changing Radio #1, ALWAYS be sure the proper microphone for the

radio is connected to the MK2R RJ45 MIC jack BEFORE connecting the DC37

RADIO cable.

If dissimilar radios are attached to MK2R or MK2R+, NEVER connect the

microphone of the Radio #2 to the RJ45 microphone jack on the rear panel.

If your radio supports firmware upload

DO NOT perform any radio upgrade through MK2R.

Remember, under Windows,

micro

HAM

USB Device Router must be running

anytime

the interface is used (not just for setup). If Router is not running, the

virtual COM ports will disappear and the device cannot be accessed!

Содержание MK2R
















































































Результаты поиска

Содержание MK2R

Отзывы:

Похожие инструкции для MK2R

Бренды по названию

Популярные бренды

microHAM MK2R, Руководство пользователя

Результаты поиска

Содержание MK2R

Отзывы:

Похожие инструкции для MK2R

Бренды по названию

Популярные бренды