microHAM MK2R Скачать руководство пользователя страница 79

Страница: 79 / 80

●

Function control:

This command selects Function 1 – 8

SAs<CR> ApplyScenario(scenarioIndex)

●

DVK, CW and FSK messages:

These commands control playing and recording of messages. The

current operating mode (determined from the radio or Router if the radio is not CAT capable) will be
used to determine if Voice, CW or FSK messages will be played/recorded.

Abort::

This command aborts the current message and clears message queue.

MA<CR> AbortMessage()

Playback:

This command starts message playback – index is 1 to 9

MPm<CR> PlayMessage(msgIndex)

This command starts message playback in a loop – index is 1 to 9, interval is 0 to 9 seconds.

MPImi<CR> PlayMessagePeriodically(msgIndex, interval)

Record:

This command starts message recording – index is 1 to 9

MRm<CR> StartMessageRecording(msgIndex)

This command stops message recording.

MRS<CR> StopMessageRecording()

DVK Message Bank Select:

This command selects voice message bank – applies only to DVK.

MBname<CR> SetMessageBank(msgName)

Содержание MK2R
















































































Результаты поиска

Содержание MK2R

Отзывы:

Похожие инструкции для MK2R

Бренды по названию

Популярные бренды

microHAM MK2R, Руководство пользователя

Результаты поиска

Содержание MK2R

Отзывы:

Похожие инструкции для MK2R

Бренды по названию

Популярные бренды