Michell Instruments Liquidew EExd Скачать руководство пользователя страница 14

Страница: 14 / 90

Liquidew EExd User’s Manual

97097 Issue 14.1, November 2019

INSTALLATION

Any power connection cable should be 3 core over sleeved, with minimum 0.5mm

insulation and rated at 300 V. Cables should have Live (L), Neutral (N) and Earth

[Ground] (E) conductors. Ensure suitably rated power supply cables and glands are

used to ensure that electrical safety is maintained. Connect each of the Live (L), Neutral

(N) and Earth [Ground] (E) conductors to the similarly marked terminals (L, N, E) on the

Power In connector shown in

Figure 3. Ensure the power supply can deliver sufficient

power consumption requirement.

Any power supply terminals and voltages must be suitably separated from the other I/O

requirements of this product.

Before applying power, perform a continuity test to ensure that the power supply cable

and product are effectively connected to the protective Earth.

The Protective Earth terminal is mounted internally and the Earth wire connected to it

should never be disconnected. The product enclosure is supplied with an external earth

stud at the lower right hand side. At installation, connect this earth stud to plant earth

by a minimum 4mm

earthing bonding. M6 stud and 2 off M6 nuts and washers, all

nickel plated.

Figure 3

Earthing Stud And Nut Washer Assembly

Fuse: A replacement fuse can be obtained by contacting Michell Instruments' technical

support. Fuse rating = 5 x 20mm 2.5 A anti-surge to IEC 60127-2.

This product is designed to be safe at least under the following conditions: between a

temperature range of -40 to +60°C (-40 to +148°F), in maximum 80% relative humidity

for temperatures up to +31°C (+88°F) decreasing linearly to 50% RH at +50°C

(+122°F). Supply voltages of ±10% and transient over voltages up to Overvoltage

Category II. Pollution Degree 2. Altitudes up to 2000m. Outdoor mounting is permitted

using suitably rated glands equivalent to NEMA 4 / IP66. See Appendix A, Technical

Specification, for full operating parameters.

Do not remove or exchange any of the cables or electrical components supplied with

this product. Doing so will invalidate all warranties.

There are no additional or special electrical safety requirements other than those

referred to in this manual.

Содержание Liquidew EExd



























































































Результаты поиска

Содержание Liquidew EExd

Отзывы:

Бренды по названию

Популярные бренды

Michell Instruments Liquidew EExd, Руководство пользователя

Результаты поиска

Содержание Liquidew EExd

Отзывы:

Бренды по названию

Популярные бренды