background image

Form 44201460 

11 

Mar 2019 

 

HEATER SIZING GUIDELINES 

7.0)

Radiant heaters work like the sun to emit radiant heat directly to the space to increase the comfort of the patio 
guests. Suitable applications include patios, porches, outdoor shopping areas and pathways. 
The amount of temperature increase in outdoor patio spaces will be dependent on the following factors: 
1.

 

The number of heaters in the space is important to provide good coverage of the area to be heated. 

2.

 

Take  care  not  to  mount  the  heaters  too  low  or  too  close  together  this  can  make  people  directly  below  the 
heaters uncomfortable. 

3.

 

It is recommended to use a suitable windbreak to reduce the effects of direct wind on the patio. If an area is 
going to be unprotected and is a breezy location then  heaters may need to  be located closer together. Wind 
breaks must be designed to allow fresh air for ventilation. 

4.

 

Angling the heaters greater than 30 degrees should be avoided unless the mounting height is low, when the 
heaters are angled more than 30 degrees the radiant intensity is lower and will reduce the amount of heat felt 
by the guests. 

 When  angle  mounting  the  heater  the  radiant  output  will  decrease  approximately  by 

following:  

Mounting Angle 

15 degree 

30 degree 

45 degree 

60 degree 

Radiant output reduction 

3% 

13% 

29% 

50% 

 

5.

 

It is recommended to place the heaters in the area of greatest heat loss facing into the patio area. 

 

The table below shows minimum area coverage per heater for outdoor patio heating based on a 5 to 10°F (2.8 to 
5.6°C) temperature rise. 
 

Mounting Angle 

Mounting Height 

Breezy Exposed 

Location 

Moderately 

Protected 

Well 

Protected 

Horizontal 

8ft. – 11ft.  

(2.5 – 3.0m) 

8 x 8 ft 

(2.5 x 2.5m) 

10 x 10 ft. 

(3.0 x 3.0m) 

12 x 12 ft. 

(3.7 x 3.7m) 

Up to 30 Degrees Angled 

7ft. – 9ft. 

(2.1 – 2.7m) 

8 x 8 ft 

(2.5 x 2.5m) 

9 x 9 ft. 

(2.7 x 2.7m) 

11 x 11 ft. 

(3.3 x 3.3m) 

30 to 60 Degrees Angled 

6ft. – 8ft. 

(1.8 – 2.5m) 

Not Recommended 

8 x 8 ft. 

(2.5 x 2.5m) 

 
Note: When sizing the number of heaters to warm the patio, the area coverage given above may not provide the 
stated temperature rise under all weather conditions and will be dependent on heater placement. Minimums are 
shown as a guideline for human comfort.  For more assistance with patio heater sizing and layout please contact 
your local Mestek, Inc. representative. 
 

 

TYPICAL HEATER LAYOUTS 

8.0)

The diagram below shows the recommended spacing layout between heaters. 
 

 

Dimension 

Horizontal 

15 to 30 degree angle 

Above 30 degree angle 

Min. 

Max. 

Min. 

Max. 

Min. 

Max. 

A. Mounting Height 

8ft (2.5m) 

11ft (3.4m)  7ft (2.1m) 

9ft (2.7m) 

6ft (1.8m) 

8ft (2.5m) 

B.  Distance  to  the  end  of 
the patio 

0ft (0m) 

6ft (1.8m) 

0ft (0m) 

6ft (1.8m) 

0ft (0m) 

6ft (1.8m) 

C. 

Distance 

between 

heaters. 

8ft (2.5m) 

12ft (3.7m)  7ft (2.1m) 

11ft (3.4m)  6ft (1.8m) 

10ft (3.0m) 

Содержание 44625000














































Отзывы: