MERRICK MC3 35.00.EX Скачать руководство пользователя страница 17

Страница: 17 / 69

Item Description

37.50 lb

Net (material) weight in the hopper. Also called Immediate Weight.

Graphical representation of the Fill Weight. See Fill Weight, page 26.

Graphical representation of the Heel Weight. See Heel Weight, page
26.

0.0%

Speed Demand Signal for the feeding device.

GT:

Grand Total. See Page 18.

Action Menu

Button to reach the Action Menu. See Action Menu, page 17.

ST:

Sub Total. See Page 18

Local Setpoint

Button to reach the Setpoint Menu. See Setting the Setpoint,
page15.

BT:

Actual Batch Total.

SP:

Actual Batch Setpoint.

“Idle”

Variable text for Batch State. See Feeder States on page 6.

“ “ (Empty)

Help text for Batch State. See Feeder States on page 6.

“Stable”

Stable weight indicator. Blank when the hopper weight is unstable.

11/22/04

Date. Format: Month/Day/Year.

01:45 PM

Time. Format: Hour (0-12):Minute AM/PM.

Batch Statistics

Button to reach the Batch Statistics screen.

Batch Statistics Screen

A statistics screen is available to monitor immediate data about the current batch, as well
as some statistics.

Batch Statistics Screen

Item Description

Fast Feed

Variable text for Batch State. See Feeder States on page 6.

SetP

Current Batch Setpoint.

Curr:

Actual (live) Batch total.

Batch Total for previous batch.

Accu:

100

Total

Batch

int

Setpo

•

∑

(Averaged batch accuracy).

Wt:

Weight of material in hopper.

Rate:

Actual (live) feedrate.

Cntr:

Batch counter. Increments for every completed batch.

High:

Highest Batch Total since statistics were cleared.

Low:

Lowest Batch Total since statistics were cleared.

Ave:

Average Batch Total since statistics were cleared.

35.00.EX O&M Manual

Содержание MC3 35.00.EX






































































Результаты поиска

Содержание MC3 35.00.EX

Отзывы:

MERRICK MC3 35.00.EX, Руководство по эксплуатации и обслуживанию, Страница: 17 / 69

Результаты поиска

Содержание MC3 35.00.EX

Отзывы: