MERRICK MC3 35.00.EX Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 69

MERRICK MC3 35.00.EX Скачать руководство пользователя страница 64

Analog Diagnostics

Analog inputs use a 20 bit A/D converter, just like the HPAD. In the Input section, you
can see

•

The counts, directly from the A/D converter. For a 4-20 mA or 2-10V input, the value
should stay between approximately 200,000 and 1,000,000.

•

The percentage of full scale of the analog input.

•

The calculated engineering value based on the scaling.

See Analog Inputs on page 30.

Digital Diagnostics

The screen offers two views of all digital input and outputs. The mapping view displays
mapping, qualifiers and status of all physical outputs and all logical inputs. The List View
displays either all logical I/O points or all physical I/O points. For more information see
Digital I/O Mapping on page 34.

Mapping view

Physical Outputs and Logical Inputs, Mapping View

The button between the up and down arrows toggles between Outputs and Inputs. Use
the up and down arrow buttons to page the digital I/O points. This screen displays the
current mapping, properties and status for the logical inputs and physical outputs.

NOTE

:

You can only see used (mapped) logical outputs and physical inputs in this view. To see
all logical outputs and physical inputs, push the

Display List

button. This will take you to

the List View.

There are seven columns in the mapping view:

ST

(Status)

Current state of I/O point. - OFF - ON

Physical

Name of physical I/O point

Logical

Name of logical I/O point

IV

(Inversion)

1 - Physical I/O point is inverted.

FW

(Qualifiers)

F – Logical I/O point generates a Fault when on. W – Logical I/O point
generates a Warning when on.

FC

(Forcing)

0 – Physical I/O point Forced Off. 1 – Physical I/O point Forced On.

35.00.EX O&M Manual

60

«
...
62
63
64
65
66
...
»

Содержание MC3 35.00.EX






































































Отзывы:

Нет отзывов