MERRICK MC3 35.00.EX Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 69

MERRICK MC3 35.00.EX Скачать руководство пользователя страница 34

Backlite Off

The fluorescent light behind the screen can be turned off if the touch screen is not used,
just like a screen saver on a PC. Set the turn-off time here. A value of 0 will keep the
back light on forever.

Displayed FR

Dampening factor for the

Rate:

indication in the Batch Statistics screen. Increase this

number if the indication is too unstable to be useful.

Loss Slots

The Rate is calculated by taking the difference between two weight values and divide by
the time difference.

Loss Slots

in the number of samples that separates the two values.

Setpoint Slots

If you are using an analog input for the Batch Setpoint, you may have to average (low
pass filter) setpoint samples to get a reliable setpoint value. Increase this number if the
setpoint value in the main screen is noisy.

Date/Time Settings

You can adjust the date and time settings here, in 24 hour format.

Parameter Min

Max

Year 0

99

Month 1

12

Day 1

31

Hour 0

23

Minute 0

59

Seconds 0

59

INPUTS AND OUTPUTS MENU

The I/O system is comprehensive and highly configurable. You reach all the settings and
configuration options from this menu.

Inputs and Outputs Menu

Analog Inputs Setup

The analog inputs can be used for (mapped to) Analog Setpoint or Panel Meter. Two
analog inputs are available when there are two PCIO boards installed. Once the inputs
are mapped, you should adjust the high, low and scaling values.

35.00.EX O&M Manual

30

«
...
32
33
34
35
36
...
»

Содержание MC3 35.00.EX






































































Отзывы:

Нет отзывов