MERRICK MC3 35.00.EX Скачать руководство пользователя страница 62

Страница: 62 / 69

Counter Description

Bad Message Counter. The MC³ does not understand
the incoming telegram.

Communication Interrupts Counter. Increments for every
character transmitted or received.

UART Status Register

States, IIR

IIR, UART Interrupt Identification Register

Value Description

Modem status changed

No interrupt pending

Transmitter buffer empty

No interrupt pending

Receiver buffer full

No interrupt pending

Receiver buffer full and receive character error

No interrupt pending

States, LSR

UART Line Status Register, bit encoded

Bit Description

Bit 7 Not used.

Bit 6 Transmitter Empty

1 - No byte in transmitter hold or transmitter shift register
0 - One byte in transmitter hold or transmitter shift register

Bit 5 Transmitter Buffer Empty

1 - no byte in Transmitter Hold Register
0 - one byte in Transmitter Hold Register

Bit 4 Break.

1 – Break Detected
0 - No Break Detected

Bit 3 Framing Error

1 – Framing Error Detected
0 - No Framing Error Detected

Bit 2 Parity Error

1 – Parity Error Detected
0 - No Parity Error Detected

Bit 1 Overrun Error

1 – Overrun Error Detected
0 - No overrun error Detected

Bit 0 Receive Data Ready

1 - Received data in receiver buffer register
0 - No Received Data

States, RX

Receiver Driver State

Value Description

Waiting for start char

35.00.EX O&M Manual

Содержание MC3 35.00.EX






































































Результаты поиска

Содержание MC3 35.00.EX

Отзывы:

MERRICK MC3 35.00.EX, Руководство по эксплуатации и обслуживанию, Страница: 62 / 69

Результаты поиска

Содержание MC3 35.00.EX

Отзывы: