MERRICK MC3 35.00.EX Скачать руководство пользователя страница 55

Страница: 55 / 69

If there are more than one load cells supporting the hopper, add the load cells capacities.
For example, for three 1000 lb load cells:

1361

2.204

1000

Cells

Load

Capacity

If the load cells are 3 mV/V, and the Design Weight is 400 kg, then:

mV/V

0.8817

1361

400

mV/V

ECAL

Enter ECAL Liveload

, in Calibrate Settings, before running the procedure. The hopper

must be empty, and a Zero Procedure must be performed immediately before the E-Cal
Procedure.

To start the test, push the

Ecal

button from the Calibration menu.

If the

ECAL Live Load

value is incorrect or if you do not wish to complete the E-Cal

Procedure for any reason, push the

Cancel

button to return to the Calibration menu. If

you are ready to execute the E-Cal Procedure, push the

Start

button.

The procedure goes through two phases. In the first phase, the HPAD sets up a known
artificial load cell signal, in mV/V.

In the second phase, the artificial weight indication in sampled.

35.00.EX O&M Manual

Содержание MC3 35.00.EX






































































Результаты поиска

Содержание MC3 35.00.EX

Отзывы:

MERRICK MC3 35.00.EX, Руководство по эксплуатации и обслуживанию, Страница: 55 / 69

Результаты поиска

Содержание MC3 35.00.EX

Отзывы: