MERRICK MC3 35.00.EX Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 69

MERRICK MC3 35.00.EX Скачать руководство пользователя страница 19

Warnings screen

There is an active indicator to the left of the text ( = On = Off). There is also a “did
occur” indicator to the left of the active indicator. You can acknowledge one warning at
a time. Use the up and down arrow buttons to move the selection box to the Warning you
want to acknowledge, and push

Acknowldg

. If you want to acknowledge all warnings,

push the

Acknowldg All

button. You can’t acknowledge an active Warning, that is, if the

active indicator is on ( ).

Faults

A Fault indicates a malfunction that prevents the feeder from running. Any logical input or
output can be configured to qualify a fault. See Digital I/O Mapping on page 34. The Fault
button is visible in the main screen if there is an active fault condition or there has been a
fault condition that has not yet been acknowledged.

Main Screen with Faults Indicator

Pushing the Fault button takes you to the Fault screen. The following screen shot shows
the default faults. Your I/O configuration may be different, producing a different Faults
screen.

Faults screen

The Faults Screen works just like the Warnings Screen. You can’t start the feeder if the
there is an unacknowledged Fault.

SETTING THE SETPOINT

You reach the Setpoint Screen by pushing the

Setpoint

button in the Main or Statistics

Screen. The button may be password protected. When a password is setup, you will
have to enter a password.

35.00.EX O&M Manual

15

«
...
17
18
19
20
21
...
»

Содержание MC3 35.00.EX






































































Отзывы:

Нет отзывов