Merlin MJ3800 Скачать руководство пользователя | Manualshive

Страница: 21 / 24

background image

21

Your door opener is programmed with self-diagnostic

capabilities. The “Learn” button/diagnostic LED will flash a

number of times then pause signifying it has found a

potential issue. Consult Diagnostic Chart below.

Diagnostic Chart

Symptom: One or both of the Indicator lights on the safety reversing sensors do not

glow steady.

• Inspect sensor wires for a short (staple in wire), correct wiring polarity

(black/white wires reversed), broken or disconnected wires, replace/attach as

needed.

• Disconnect all wires from opener.
• Remove sensors from brackets and shorten sensor wires to 30-60mm (1-2”)

from back each of sensor.

• Reattach sending eye to opener using shortened wires. If sending eye indicator

light glows steadily, attach the receiving eye.

• Align sensors, if the indicator lights glow replace the wires for the sensors. If the

sensor indicator lights do not light, replace the safety reversing sensors.

Symptom: LED is not lit on multi-function door control.

• Inspect Multi-Function Door Control/wires for a short (staple in wire), replace as

needed.

• Disconnect wires at multi-function door control, touch wires together. If opener

activates, replace multi-function door control.

• If opener does not activate, disconnect multi-function door control wires from

opener. Momentarily short across red and white terminals with jumper wire. If

opener activates, replace multi-function door control wires.

Symptom: Sending indicator light glows steadily, receiving indicator light is dim or

flashing.

• Realign receiving eye sensor, clean lens and secure brackets.
• Verify door track is firmly secured to wall and does not move.

Symptom: The RPM Sensor = Short travel 150-200mm (6-8").

• Unplug unit to reset. Try to operate opener, check diagnostic code.
• If it is still flashing 5 times and opener moves 150-200mm (6-8"), the unit’s APE

(Absolute Positioning Encoder) may need to be replaced, for details contact your

Chamberlain reseller.

Symptom: Door reverses while closing.

• Check for possible door obstructions and remove.
• Check that the cable tension monitor is properly connected to the opener.
• Replace the cable tension monitor.

Cable tension monitor

reversal.

Possible RPM sensor

failure. Unplug to reset.

Safety reversing sensors

slightly misaligned

(dim or flashing LED).

multi-function

door control or

wire shorted.

Safety reversing sensors

wire shorted or black/white

wire reversed.

Safety reversing sensors

wire open (broken or

disconnected).

1 FLASH

2 FLASHES

3 FLASHES

4 FLASHES

5 FLASHES

9 FLASHES

OR

“Learn”

Button LED

or Diagnostic

LED

“Learn”

Button

Installed

Safety Reversing

Sensor

«
...
19
20
21
22
23
...
»

Содержание MJ3800

























Отзывы:

Нет отзывов

Похожие инструкции для MJ3800

Бренд: Telcoma Automations Страницы: 68

Бренд: Honeywell Страницы: 2

Бренд: Honeywell Страницы: 4

Бренд: Proteco Страницы: 10

Automatic Gate Opener System

Бренд: Mighty Mule Страницы: 44

Бренд: RIB Страницы: 28

Бренд: Doco Страницы: 23

Бренд: V2 Страницы: 88

Бренд: FAAC Страницы: 12

Бренд: Calimet Страницы: 17

Бренд: CAME Страницы: 128

Бренд: vds Страницы: 13

SPIDER QK-S400KIT

Бренд: quiko Страницы: 22

Бренд: Chamberlain Страницы: 40

UNV-Light LO TB

Бренд: LOBAS Страницы: 56

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды