manualshive.com logo in svg

Merlin MJ3800, Инструкция по установке и эксплуатации

Поделиться
Скачать
Merlin MJ3800 Скачать руководство пользователя страница 13

13

Invisible Light Beam
Protection Area

S ensor

Sensor

Safety Reversing Sensor

Bell Wire

Bell Wire

Opener

Safety Reversing Sensor

Power Door Lock

Quick-Connect Terminals

WHT/BLK

WHT

Sensor
Connections

To Power
Door Lock

To Multi-function
Control Panel

Connect Wire to
Quick-Connect
Te rminals

red

white

MAX height
100mm (4”)
MIN height
50mm (2”)

TROUBLESHOOTING THE SAFETY REVERSING

SENSORS

1. If the

sending eye

indicator LEDs are both flashing

after installation, check for:

• Electric power to the opener.
• A short in the white or white/black wires. These can occur at staples, or at opener connections.
• Incorrect wiring between safety reversing sensors and opener.
• A broken wire.
2. If the sending eye indicator light

glows steadily

but the receiving eye indicator light doesn't:

• Check alignment.
• Check for an open wire to the

receiving eye

.

3. If the

receiving eye

indicator light is dim, realign

either sensor.

NOTE: When the invisible beam path is obstructed or misaligned while the door is closing, the door will reverse.

If the door is already open, it will not close and the LED indicator light will flash 10 times. See page 21.

AUTOMATIC CLOSE TIMER FUNCTION

Note:

Requires the Chamberlain Protector System

TM

(IR-sensors) to be installed. If Protector System

TM

(IR-sensors) is

installed to enable the timer to close function (first time), install sensors, close the garage door and wait for 5 minutes.

A Multi-function Door Control is required to enable and disable the auto-close function.

Enable:

Push and hold lock button on the Multi-function Door Control until the electric lock toggled twice. Release the

lock button, at the same time watch the LED light in the center of the actuator button from the Multi-function Door

Control.

1x flash 10 seconds Auto-Close

2x flash 45 seconds Auto-Close

3x flash 2 minutes Auto-Close

4x flash 3 minutes Auto-Close

5x flash OFF Auto-Close

Factory setting is OFF. Repeat the procedure until the Multi-function Door Control shows the required number of flashes.

Auto close is NOT recommended for households with

young children.

Door may operate unexpectedly, therefore do not

allow anything to stay in the path of the door.

Содержание MJ3800

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды