Merlin MJ3800 Скачать руководство пользователя

Страница: 6 / 24

ASSEMBLY STEP 1

Attach the Collar to the Opener
To avoid installation difficulties, do not run the door

opener until instructed to do so.

• Loosen the collar screws.
• Attach collar to either the left or the right side of the

opener. Depending on Left or Right hand installation

ensure that the collar is seated all the way on motor

shaft until stop is reached (Figure 1).

• Position the collar so that the screws are accessible

when attached to the torsion bar.

• Tighten both sides of collar screws equally (Figure 2) to

secure collar to the opener (16Nm-19Nm of torque).

• Do not tighten set screws as yet.

NOTE: Nylon Patch has been added to the collar

screws, so it is normal for some thread resistance to

be evident.

Collar Screw

Set Screw

Collar Screw

Set Screw

ASSEMBLY STEP 2

Attach Mounting Bracket to Opener

• Loosely attach slotted side of mounting bracket

to the same side of the opener as the collar,

using self-threading screws provided.

NOTE: Do not tighten until instructed. Illustrations

shown are for left side installation.

Socket Wrench

Figure 1

RIGHT

WRONG

Figure 2

Screw

#10-32

HARDWARE SHOWN ACTUAL SIZE

To prevent possible SERIOUS INJURY or DEATH,

the collar MUST be properly tightened. The door

may not reverse correctly or limits may be lost

due to collar slip.

Alternate Mounting Kit (NOT SUPPLIED):

This kit allows model MJ3800 to be

mounted below the torsion bar in the

case where the torsion bar is not

round or the normal mounting area

is obstructed.

G480LM

Left hand
installation

Right hand
installation

Содержание MJ3800

























Результаты поиска

Содержание MJ3800

Отзывы:

Похожие инструкции для MJ3800

Бренды по названию

Популярные бренды

Merlin MJ3800, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MJ3800

Отзывы:

Похожие инструкции для MJ3800

Бренды по названию

Популярные бренды