Merlin MJ3800 Скачать руководство пользователя

Страница: 9 / 24

WHT/GRN

To insert or release wire,

push in tab with

screwdriver tip

Cable Tension

Monitor

Strip wire (11mm)

WHT/GRN

Cable

Tension

Monitor

Cable Tension

Monitor Roller

Cable

2"-6"

(5 cm-

15 cm)

Drum

Torsion Bar

Opener

1/8"-1/4"

(3 mm-6 mm)

With Door Closed

Preferred Orientation

Figure 1

Hex

Hea

d S

cre

(2)

Scre

(2)

Wall

Anc

hor

(2)

Staples

Figure 3

INSTALLATION STEP 4

Attach the Cable Tension Monitor (Required)

Your MJ3800 is supplied with a cable tension monitor.

This safety device is supplied to monitor the cable for

ANY slack that may occur and will reverse the door

when excessive slack is detected, eliminating service

calls.
The cable tension monitor

MUST

be connected and

properly installed before the door opener will move in

the down direction.

NOTE: The cable tension monitor is shipped for left

side installation. It is preferred that the cable tension

monitor be installed on the same side of the door as

the opener.

If required, it can be mounted on the opposite side of

door. Remove the snap-ring holding the roller in place

and reassemble it on the opposite side of the cable

tension monitor.

1.Position the cable tension monitor as shown

(Figures 1 and 2). The cable tension monitor

should be located as close to the drum as

possible.

NOTE: There must be no obstructions in the

installation area that prevent the cable tension

monitor or the cable itself from closing completely

when slack is detected.

2.Make sure cable tension monitor is located over

a wood support member.

NOTE: If the cable tension monitor can not be

mounted into wood with the lag screws provided, it

can be mounted into 25mm (1”) or greater pasterboard

using the wall anchors (2) and the #8 hex head screws

(2) provided in the hardware bag.

3.Mark and drill 5mm (3/16”) pilot holes for screws

(pilot holes are not required for anchors).

4.Attach the cable tension monitor to the wall

using the hardware provided. Make sure that the

roller is on top of the cable.

5.Run bell wire to opener. Use insulated staples to

secure wire in several places.

6.Connect bell wire to the green quick-connect

terminals (polarity is not important) (Figure 3).

NOTE: Cable must have tension through entire travel.

Make sure there is no slack in cable on opposite side

of the door during normal operation. If this condition

exists, adjust cables as required.

3/4" Min.

(18 mm Min.)

Wall

Drum

Cable

Figure 2

Содержание MJ3800

























Результаты поиска

Содержание MJ3800

Отзывы:

Похожие инструкции для MJ3800

Бренды по названию

Популярные бренды

Merlin MJ3800, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MJ3800

Отзывы:

Похожие инструкции для MJ3800

Бренды по названию

Популярные бренды